Jonsered CC 2145 manual Bevel gear, Drive shaft, Spark plug, Maintenance, Cleaning the air filter

Page 30
Cleaning the air filter

MAINTENANCE

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water.

An oiled foam plastic filter (available as an accessory) must be used if the machine is operated in extremely dusty conditions. See instructions under the heading Oiling the air filter.

Oiling the air filter

Always use special filter oil. Filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect in the bottom.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

Bevel gear

The bevel gear is filled with the right amount of grease at the factory. However, before using the machine you should check that the bevel gear is filled 3/4 full with grease. Use JONSERED special grease.

The grease in the bevel gear does not normally need to be changed except if repairs are carried out.

Drive shaft

The drive shaft must be greased every three months during full-time use. Contact your dealer if you are uncertain about the procedure.

Spark plug

The spark plug condition is influenced by:

Incorrect carburetor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

30 – English

Image 30
Contents Operator’s manual EPA KEY TO SYMBOLS SymbolsNote the following before starting CONTENTSContents KEY TO SYMBOLSINTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw? BCWhat is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 W Decompression valve FC 2145 S, FC 2145 W6 - English What is what on the clearing saw? CC WARNING! Listen out for warning signals or GENERAL SAFETY PRECAUTIONSPersonal protective equipment WARNING! The ignition system of thisMachine′s safety equipment WARNING! Never use a machine with faultyA BA B Quick release Cutting attachment guardVibration damping system MufflerWARNING! Mufflers fitted with catalytic Locking nutLocking screw WARNING! The inside of the muffler containGeneral rules Cutting equipmentWARNING! Using an incorrect cutting WARNING! Always stop the engine beforeSharpening the saw blade Trimmer headTransport position, handlebar ASSEMBLYAssembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 W Assembling the handlebar and throttle BC 2145, CCWARNING! When fitting the cutting L M C AAssembling the cutting equipment N E F P BA CL M C A Fitting the blade guard and saw bladeFitting the trimmer guard and trimmer head Trimmy SII H P B CStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments WARNING! When using a clearing saw itVector harness 2 Grass clearingFuel Fuel safetyFUEL HANDLING WARNING! Take care when handling fuelWARNING! The catalytic converter muffler FuelingWARNING! Taking the following precautions will lessen the risk of fire Do not smoke or place hot objects near fuelStarting and stopping STARTING AND STOPPINGCheck before starting WARNING! The complete clutch cover andStopping WARNING! When the engine is started withStarting Heated handles FC 2145 WWORKING TECHNIQUES General working instructionsWARNING! Neither the operator of the WARNING! Sometimes branches or grass Working methodsWARNING! Watch out for thrown objects WARNING! Machines fitted with saw bladesGrass clearing using a grass blade Brush cutting with a saw bladeCutting TrimmingClearing SweepingMAINTENANCE CarburetorWARNING! If the idle speed cannot be Setting procedure without a load Blade can be used Setting procedure with a load Trimmer head should be usedFC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Air filter MufflerCooling system Proceed as followsSpark plug Bevel gearDrive shaft Cleaning the air filterWinter use Temperature 5C 41F or coldermaintenance Maintenance scheduleMaintenance DailyWeight TECHNICAL DATATechnical data FC 2145 SEngine Cutting attachment guard, Art. no Approved accessoriesType FC 2145, FC 2145 S, FC 2145 WFEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSPoly Trim 6 Nm20mm 7,0 m Trimmy SII095-.130 ~ 3,5 mPage 1,1 Kw Auto1,1 Kw 2,7-3,3 mm10 cm 4,3 m Tap n’Go 45 Spin10 m 2,7-3,3 mm´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨