Jonsered CC 2145 manual Starting And Stopping, Check before starting, Starting and stopping

Page 21
STARTING AND STOPPING

STARTING AND STOPPING

Check before starting

•Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

•Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked.

•Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

•Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked.

Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked.

•Never use the machine without a guard nor with a defective guard.

•All covers must be correctly fitted and undamaged before you start the machine.

Starting and stopping

WARNING! The complete clutch cover and

!shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Always move the machine away from the refuelling area before starting. Place the machine on a flat surface. Ensure the cutting attachment cannot come into contact with any object.

Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Cold engine

Ignition: Set the stop switch to the start position.

Choke: Set the choke control (A) in the choke position.

Primer bulb: Press the air purge diaphragm (B) repeatedly until fuel begins to fill the diaphragm.The diaphragm need not be completely filled.

Warm engine

Use the same starting procedure as for a cold engine but without setting the choke control in the choke position.

Start throttle: (BC 2145, CC 2145)

Set the throttle to the start position by first pressing the throttle lockout and the throttle trigger, then pressing the start throttle button (A). Then release the throttle lockout and the throttle trigger, followed by the start throttle button. The throttle function is now activated. To return the engine to idle, press the throttle lockout and throttle trigger again.

English – 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s manual EPA Symbols KEY TO SYMBOLSContents CONTENTSNote the following before starting KEY TO SYMBOLSDear customer INTRODUCTIONWhat is what on the clearing saw? BC WHAT IS WHAT?What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 W Decompression valve FC 2145 S, FC 2145 W6 - English What is what on the clearing saw? CC Personal protective equipment GENERAL SAFETY PRECAUTIONSWARNING! Listen out for warning signals or WARNING! The ignition system of thisMachine′s safety equipment WARNING! Never use a machine with faultyA BA B Vibration damping system Cutting attachment guardQuick release MufflerLocking screw Locking nutWARNING! Mufflers fitted with catalytic WARNING! The inside of the muffler containWARNING! Using an incorrect cutting Cutting equipmentGeneral rules WARNING! Always stop the engine beforeTrimmer head Sharpening the saw bladeAssembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 W ASSEMBLYTransport position, handlebar Assembling the handlebar and throttle BC 2145, CCAssembling the cutting equipment L M C AWARNING! When fitting the cutting N E F P BA CFitting the trimmer guard and trimmer head Trimmy SII Fitting the blade guard and saw bladeL M C A H P B CFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness WARNING! When using a clearing saw it2 Grass clearing Vector harnessFUEL HANDLING Fuel safetyFuel WARNING! Take care when handling fuelWARNING! Taking the following precautions will lessen the risk of fire FuelingWARNING! The catalytic converter muffler Do not smoke or place hot objects near fuelCheck before starting STARTING AND STOPPINGStarting and stopping WARNING! The complete clutch cover andStarting WARNING! When the engine is started withStopping Heated handles FC 2145 WWORKING TECHNIQUES General working instructionsWARNING! Neither the operator of the WARNING! Watch out for thrown objects Working methodsWARNING! Sometimes branches or grass WARNING! Machines fitted with saw bladesBrush cutting with a saw blade Grass clearing using a grass bladeClearing TrimmingCutting SweepingMAINTENANCE CarburetorWARNING! If the idle speed cannot be Setting procedure without a load Blade can be used Setting procedure with a load Trimmer head should be usedFC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Cooling system MufflerAir filter Proceed as followsDrive shaft Bevel gearSpark plug Cleaning the air filterTemperature 5C 41F or colder Winter useMaintenance Maintenance schedulemaintenance DailyTechnical data TECHNICAL DATAWeight FC 2145 SWeight Type Approved accessoriesCutting attachment guard, Art. no FC 2145, FC 2145 S, FC 2145 WYOUR WARRANTY RIGHTS AND OBLIGATIONS FEDERAL EMISSION CONTROL WARRANTY STATEMENTPoly Trim 6 Nm20mm 095-.130 Trimmy SII7,0 m ~ 3,5 mPage 1,1 Kw Auto1,1 Kw 2,7-3,3 mm10 m Tap n’Go 45 Spin10 cm 4,3 m 2,7-3,3 mm´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨
Top Page Image Contents