Jonsered CC 2145 manual Fueling, Fuel Handling, WARNING! The catalytic converter mufﬂer

Page 20

WARNING! The catalytic converter mufﬂer

FUEL HANDLING

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by ﬁlling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before ﬁlling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

WARNING! The catalytic converter mufﬂer

!gets very hot during and after use. This also applies during idling. Be aware of the ﬁre hazard, especially when working near ﬂammable substances and/or vapours.

Fueling

WARNING! Taking the following precautions,

!will lessen the risk of ﬁre:

Do not smoke or place hot objects near fuel.

Always shut off the engine before refuelling.

Always stop the engine and let it cool for a few minutes before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

•Clean the area around the fuel cap. Contamination in the tank can cause operating problems.

•Ensure that the fuel is well mixed by shaking the container before ﬁlling the tank.

20 – English

Image 20

Contents Operator’s manual EPA KEY TO SYMBOLS SymbolsCONTENTS ContentsNote the following before starting KEY TO SYMBOLSINTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw? BC6 - English What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 WDecompression valve FC 2145 S, FC 2145 W What is what on the clearing saw? CC GENERAL SAFETY PRECAUTIONS Personal protective equipmentWARNING! Listen out for warning signals or WARNING! The ignition system of thisA BA B Machine′s safety equipmentWARNING! Never use a machine with faulty Cutting attachment guard Vibration damping systemQuick release MufﬂerLocking nut Locking screwWARNING! Mufﬂers ﬁtted with catalytic WARNING! The inside of the mufﬂer containCutting equipment WARNING! Using an incorrect cuttingGeneral rules WARNING! Always stop the engine beforeSharpening the saw blade Trimmer headASSEMBLY Assembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 WTransport position, handlebar Assembling the handlebar and throttle BC 2145, CCL M C A Assembling the cutting equipmentWARNING! When ﬁtting the cutting N E F P BA CFitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SIIL M C A H P B CAdjusting the harness and clearing saw Fitting other guards and cutting attachmentsStandard harness WARNING! When using a clearing saw itVector harness 2 Grass clearingFuel safety FUEL HANDLINGFuel WARNING! Take care when handling fuelFueling WARNING! Taking the following precautions will lessen the risk of ﬁreWARNING! The catalytic converter mufﬂer Do not smoke or place hot objects near fuelSTARTING AND STOPPING Check before startingStarting and stopping WARNING! The complete clutch cover andWARNING! When the engine is started with StartingStopping Heated handles FC 2145 WWARNING! Neither the operator of the WORKING TECHNIQUESGeneral working instructions Working methods WARNING! Watch out for thrown objectsWARNING! Sometimes branches or grass WARNING! Machines ﬁtted with saw bladesGrass clearing using a grass blade Brush cutting with a saw bladeTrimming ClearingCutting SweepingWARNING! If the idle speed cannot be MAINTENANCECarburetor FC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Setting procedure without a load Blade can be usedSetting procedure with a load Trimmer head should be used Mufﬂer Cooling systemAir ﬁlter Proceed as followsBevel gear Drive shaftSpark plug Cleaning the air ﬁlterWinter use Temperature 5C 41F or colderMaintenance schedule Maintenancemaintenance DailyTECHNICAL DATA Technical dataWeight FC 2145 STECHNICAL DATA Approved accessories TypeCutting attachment guard, Art. no FC 2145, FC 2145 S, FC 2145 WFEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS20mm Poly Trim6 Nm Trimmy SII 095-.1307,0 m ~ 3,5 mPage Auto 1,1 Kw1,1 Kw 2,7-3,3 mmTap n’Go 45 Spin 10 m10 cm 4,3 m 2,7-3,3 mm´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨