Snapper LT23460AWS IMPORTANT! Before You Start Mowing, Operator Presence System Seat

Page 11

1.Remove the protective cap from the battery terminal.

2.Fasten the red cable and terminal cover (if equipped) to the positive (+) terminal with the fasteners as shown (Figure 9).

3.Fasten the black cable to the negative (-) terminal with the fasteners as shown.

C

D

E

 

A

B

 

 

 

 

F

A

 

 

 

H

G

Figure 9: Battery

A - Carriage bolt

B - Hex nut

C - Black cable

D - Positive (+) terminal

E - Red cable

F - Battery

G - Battery tray

H - Terminal cover (Also see ‘H’ in Figure 3)

IMPORTANT! Before You Start Mowing

•Check the engine oil.

•Fill the fuel tank with gasoline.

•Check the air pressure of the tires.

•Check the level of the mower housing.

•Make sure the battery cables are attached.

•Make sure the wire is attached to the spark plug.

WARNING: Before doing any assembly or maintenance to the mower, remove the wire from the spark plug.

NOTE: In this instruction book, left and right describe the location of a part with the operator on the seat.

Operator Presence System (Seat)

The seat has an Operator Presence System to shut off the engine when the operator leaves the seat. This system is not intended for regular use in stopping the engine or the blade(s). Before leaving the seat, move the blade rotation control to the DISENGAGE position, shift to neutral, set the parking brake, and stop the engine.

How To Check The Safety Interlock Switches

To check the function of the safety interlock switches, follow the steps below.

1.Check the blade rotation control switch. Sit in the seat. Depress the clutch/brake pedal. Move the blade rotation control to the ENGAGE position. Turn the ignition switch to the START position. The engine should not start. If the engine starts, the switch is defective and must be replaced.

2.Check the clutch/brake switch. Sit in the seat. Move the blade rotation control to the DISENGAGE position. DO NOT depress the clutch/brake pedal. Turn the ignition switch to the START position. The engine should not start. If the engine starts, the switch is defective and must be replaced.

3.Check the Operator Presence System switch. DO NOT sit in the seat. Depress the clutch/brake pedal. Move the blade rotation control to the DISENGAGE position. Turn the ignition switch to the START position. The engine should not start. If the engine starts, the switch is defective and must be replaced.

4.Check the Reverse Mowing Option (RMO) switch. Sit in the seat. Depress the clutch/brake pedal. Move the blade rotation control to the DISENGAGE position. Start the engine and move the drive control to the reverse

(R) position. With the engine running, move the blade rotation control to the ENGAGE position. The engine should stop running. If the engine continues to run, the RMO switch is defective and must be replaced.

English

en

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Manual No Rev. ‘-’, 2/18/2009 Lawn Tractor SeriesDate Purchased Where to Find Us MowerEngine Table of Contents Do not allow pre-teenage children to operate machine Protection for ChildrenProtection against Tipovers PreparationOperation Safe Handling of GasolineTowing Ghij International PictorialsParts Bag Contents AssemblyAssembling the Steering Wheel Installing the SeatHow to Install the Battery Cables Maintenance Free BatteryOperator Presence System Seat Remove the protective cap from the battery terminalHow To Check The Safety Interlock Switches IMPORTANT! Before You Start MowingCheck the Level of the Mower Deck How to Prepare the EngineCheck the Tires Features and Controls Attachments Using ControlsHow to Use the Throttle Control OperationDriving and Stopping the Unit How to Engage the BladesHow to Use the Speed Control Pedal How to Disconnect the Transmission How to Use the Cruise ControlHow to Drive in Reverse How to Change DirectionHow to Stop the Unit How to Set the Parking BrakeHow to Change the Cutting Height Mowing How to Transport the UnitHow to Operate the Mower Deck Remove the key to restrict access to the RMO featureAll-Wheel Steering How to Operate the Unit on HillsHow to Stop on a Hill How to Start Operation on a HillAdd Gasoline How to Start the EngineEngine Operation Before Starting the Engine Check the OilUse the left side of the mower deck to trim near an object TipsOperating Tips Mowing and Bagging TipsMaintenance engine Examine blades MaintenanceMaintenance Schedule Frequency Maintenance Required CommentsInspection How to Check the MufflerHow to Remove and Install the Blade General RecommendationsHow to Sharpen the Blade Install the mower deck. See How To Install The Mower DeckBlade Brake Check AdjustmentsHow to Check and Adjust the PTO Clutch Remove the 1/4 inch 6 mm pin or bolt Figure How to Check and Adjust the Motion Drive BeltAdjusting drive brake Drive brake Gearbox Hex nut How to Check and Adjust the Drive BrakeHow to Charge the Battery How to Remove the BatteryLift the battery tray and the battery out of the unit How to Clean the BatteryLubrication Where to LubricateHow to Install the Mower Deck Mower Deck MaintenanceHow to Check the Fuel Filter How to Remove the Mower DeckHanger rod Q Adjuster arm Remove the gauge wheels Figure How to Adjust the Gauge WheelsHow to Level the Mower Deck Axle bolts for the gauge wheels were mountedReplacing the Motion Drive Belt Loosening adjuster knobs Lift link Adjuster knobsRemove the primary mower drive belt from the stack pulley How to Replace the Primary Mower Drive BeltHow to Replace the Secondary Mower Drive Belt English Rear wheel assembly Valve stem How to Install the WheelsRemove the bolt or pin used in step Wheel AlignmentRaise the tractor hood How to Replace the FuseHow to Replace the Light Bulb How to Clean the Mower DeckStorage over 30 days Troubleshooting Chart TroubleshootingMower blades will not Pedal is depressed When the brake pedal isCorrectly Cut levelProduct Specifications SpecificationsEnglish Page English Page Year Limited Warranty Snapper Products Macon Street McDonough, GA

LT23460AWS specifications

The Snapper LT23460AWS is a versatile riding lawn mower designed for homeowners seeking efficiency, comfort, and ease of use in maintaining their lawns. This model comes equipped with several innovative features and technologies that enhance its performance and user experience.

One of the standout characteristics of the LT23460AWS is its powerful 23 horsepower Briggs & Stratton engine. This engine provides ample power to tackle various terrains, ensuring a smooth and efficient mowing experience. The mower operates on a hydrostatic transmission system, allowing users to easily adjust the speed and direction without the need for manual shifting, making it ideal for navigating around obstacles with ease.

The Snapper LT23460AWS features a 60-inch cutting deck, which allows for wide coverage in fewer passes, reducing the time spent mowing. This cutting deck is equipped with a robust cutting system, designed to deliver a clean, precise cut, whether tackling tall grass or maintaining a manicured lawn. Additionally, the deck height can be easily adjusted to suit different grass lengths, providing flexibility in lawn care.

Comfort is a key aspect of the LT23460AWS. The mower is designed with a spacious, ergonomic seat that provides ample cushioning, allowing for hours of comfortable mowing. Its easy-to-reach controls are strategically placed, enhancing user convenience and minimizing fatigue. The steering wheel is designed for optimal maneuverability, making it easier to navigate tight corners and complex landscaping.

Another notable technology in the Snapper LT23460AWS is the Advanced Air Management System. This technology optimizes airflow within the cutting deck, ensuring even grass distribution and improving overall cut quality. Moreover, the mower includes a mulching capability, allowing homeowners to cut grass into fine pieces that can enrich the lawn when returned to the soil.

The LT23460AWS is also designed with durability in mind. Its robust construction features high-quality materials that can withstand the rigors of regular mowing. This commitment to durability ensures that the Snapper LT23460AWS will provide reliable performance season after season.

In summary, the Snapper LT23460AWS is a powerful and efficient riding mower that combines advanced technology with user-friendly design. With its powerful engine, hydrostatic transmission, and comfortable seating, this mower is poised to meet the diverse needs of homeowners while delivering high-quality lawn care results.
Top Page Image Contents