Snapper LT23460AWS specifications How to Check and Adjust the Motion Drive Belt

Page 26

How to Check and Adjust the Motion Drive Belt

If the motion drive belt is loose, the belt will slip when; (1) going up a hill, (2) pulling a heavy load, or (3) the unit will not move forward. Adjust the belt as follows.

WARNING: Before you make an inspection, adjustment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident.

1.Check the routing of the motion drive belt. Make sure the belt is installed correctly and is inside all the belt guides.

2.Disconnect the clutch link from the idler arm (Figure 24).

3.Align the hole in the brake lever with the hole in the frame. Hold the brake lever in place with a 1/4 inch (6 mm) pin or bolt (Figure 25).

4.Rotate the clutch link until the mounting hole in the clutch link is aligned with the hole in the idler arm as shown in Figure 24.

5.Connect the clutch link to the idler arm (Figure 24).

6.Remove the 1/4 inch (6 mm) pin or bolt (Figure 25).

B

C

D

 

 

 

A

 

Figure 24: Aligning clutch link

A - Mounting holes

B - Idler arm

C - Clutch link

D - Clutch rod

7.If the belt still slips after the belt has been adjusted, then the motion drive belt is worn or damaged and must be replaced. See “Replacing The Motion Drive Belt”.

F

G

A

B

C

E

 

 

D

 

 

 

 

Figure 25: Adjusting motion drive belt

 

A - 1/4" (6mm) Pin or bolt

E - Motion drive belt

B - Clutch link

F - Belt guide

C - Idler arm

G - Brake lever

D - Idler spring

 

26

www.snapper.com

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Lawn Tractor Series Manual No Rev. ‘-’, 2/18/2009Date Purchased Where to Find Us MowerEngine Table of Contents Preparation Protection for ChildrenProtection against Tipovers Do not allow pre-teenage children to operate machineSafe Handling of Gasoline OperationTowing International Pictorials GhijAssembly Parts Bag ContentsInstalling the Seat Assembling the Steering WheelMaintenance Free Battery How to Install the Battery CablesIMPORTANT! Before You Start Mowing Remove the protective cap from the battery terminalHow To Check The Safety Interlock Switches Operator Presence System SeatCheck the Level of the Mower Deck How to Prepare the EngineCheck the Tires Features and Controls Operation Using ControlsHow to Use the Throttle Control AttachmentsDriving and Stopping the Unit How to Engage the BladesHow to Use the Speed Control Pedal How to Change Direction How to Use the Cruise ControlHow to Drive in Reverse How to Disconnect the TransmissionHow to Stop the Unit How to Set the Parking BrakeHow to Change the Cutting Height Remove the key to restrict access to the RMO feature How to Transport the UnitHow to Operate the Mower Deck MowingHow to Start Operation on a Hill How to Operate the Unit on HillsHow to Stop on a Hill All-Wheel SteeringBefore Starting the Engine Check the Oil How to Start the EngineEngine Operation Add GasolineMowing and Bagging Tips TipsOperating Tips Use the left side of the mower deck to trim near an objectFrequency Maintenance Required Comments MaintenanceMaintenance Schedule Maintenance engine Examine bladesGeneral Recommendations How to Check the MufflerHow to Remove and Install the Blade InspectionInstall the mower deck. See How To Install The Mower Deck How to Sharpen the BladeBlade Brake Check AdjustmentsHow to Check and Adjust the PTO Clutch How to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHow to Check and Adjust the Drive Brake Adjusting drive brake Drive brake Gearbox Hex nutHow to Clean the Battery How to Remove the BatteryLift the battery tray and the battery out of the unit How to Charge the BatteryWhere to Lubricate LubricationHow to Remove the Mower Deck Mower Deck MaintenanceHow to Check the Fuel Filter How to Install the Mower DeckHanger rod Q Adjuster arm Axle bolts for the gauge wheels were mounted How to Adjust the Gauge WheelsHow to Level the Mower Deck Remove the gauge wheels FigureLoosening adjuster knobs Lift link Adjuster knobs Replacing the Motion Drive BeltRemove the primary mower drive belt from the stack pulley How to Replace the Primary Mower Drive BeltHow to Replace the Secondary Mower Drive Belt English How to Install the Wheels Rear wheel assembly Valve stemWheel Alignment Remove the bolt or pin used in stepHow to Clean the Mower Deck How to Replace the FuseHow to Replace the Light Bulb Raise the tractor hoodStorage over 30 days Troubleshooting Troubleshooting ChartCut level Pedal is depressed When the brake pedal isCorrectly Mower blades will notSpecifications Product SpecificationsEnglish Page English Page Year Limited Warranty Snapper Products Macon Street McDonough, GA

LT23460AWS specifications

The Snapper LT23460AWS is a versatile riding lawn mower designed for homeowners seeking efficiency, comfort, and ease of use in maintaining their lawns. This model comes equipped with several innovative features and technologies that enhance its performance and user experience.

One of the standout characteristics of the LT23460AWS is its powerful 23 horsepower Briggs & Stratton engine. This engine provides ample power to tackle various terrains, ensuring a smooth and efficient mowing experience. The mower operates on a hydrostatic transmission system, allowing users to easily adjust the speed and direction without the need for manual shifting, making it ideal for navigating around obstacles with ease.

The Snapper LT23460AWS features a 60-inch cutting deck, which allows for wide coverage in fewer passes, reducing the time spent mowing. This cutting deck is equipped with a robust cutting system, designed to deliver a clean, precise cut, whether tackling tall grass or maintaining a manicured lawn. Additionally, the deck height can be easily adjusted to suit different grass lengths, providing flexibility in lawn care.

Comfort is a key aspect of the LT23460AWS. The mower is designed with a spacious, ergonomic seat that provides ample cushioning, allowing for hours of comfortable mowing. Its easy-to-reach controls are strategically placed, enhancing user convenience and minimizing fatigue. The steering wheel is designed for optimal maneuverability, making it easier to navigate tight corners and complex landscaping.

Another notable technology in the Snapper LT23460AWS is the Advanced Air Management System. This technology optimizes airflow within the cutting deck, ensuring even grass distribution and improving overall cut quality. Moreover, the mower includes a mulching capability, allowing homeowners to cut grass into fine pieces that can enrich the lawn when returned to the soil.

The LT23460AWS is also designed with durability in mind. Its robust construction features high-quality materials that can withstand the rigors of regular mowing. This commitment to durability ensures that the Snapper LT23460AWS will provide reliable performance season after season.

In summary, the Snapper LT23460AWS is a powerful and efficient riding mower that combines advanced technology with user-friendly design. With its powerful engine, hydrostatic transmission, and comfortable seating, this mower is poised to meet the diverse needs of homeowners while delivering high-quality lawn care results.
Top Page Image Contents