Snapper LT23460AWS specifications Installing the Seat, Assembling the Steering Wheel

Page 9

Installing the Seat

How to Install the Seat

1.Carefully remove the plastic bag from the seat. Use the fasteners shown below to install the seat. The fasteners are shown at full size.

A B

Figure 4: Seat parts

A - Wing bolt (Also see ‘E’ in Figure 3)

B - Washer (Also see ‘F’ in Figure 3)

NOTE: Fasteners may be attached to seat for shipping purposes, if so remove fasteners before proceeding.

2.Align the holes in the seat hinge to the holes in the seat (Figure 5). Fasten the seat to the seat hinge with the fasteners as shown.

3.Check the operating position of the seat. If the seat needs to be adjusted, loosen the two wing bolts. Slide the seat forward or backward along the seat adjusting holes as shown. Tighten the wing bolts (A).

E

 

D

 

C

B

 

 

A

Figure 5: Seat

A - Wing bolt

B - Washer

C - Seat adjusting hole

D - Seat hinge

E - Seat

English

Assembling the Steering Wheel

How to Assemble the Steering Wheel

Tools Required: 3/8" Socket Wrench

Attach the steering wheel as follows:

A

B

Figure 6: Steering wheel parts

A - Screw (Also see ‘C’ in Figure 3)

B - Washer (Also see ‘D’ in Figure 3)

1.Make sure the front wheels point forward.

2.Slide the bellows over the steering post (Figure 7).

NOTE: Before attachment of the steering wheel, make sure that the front wheels point forward and are straight. For proper alignment of the steering wheel, see Figure 7.

3.Slide the steering wheel onto the steering post.

4.Use the fasteners shown above to secure the steering wheel. The fasteners are shown at full size. Tighten the screw until snug and then add 1/4 turn. DO NOT over tighten.

5.Attach the cover to the steering wheel.

6.Some models have an optional decal in the parts bag. Attach the decal to the center of the steering wheel as shown.

en

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Manual No Rev. ‘-’, 2/18/2009 Lawn Tractor SeriesWhere to Find Us Mower EngineDate Purchased Table of Contents Protection against Tipovers Protection for ChildrenPreparation Do not allow pre-teenage children to operate machineOperation Safe Handling of GasolineTowing Ghij International PictorialsParts Bag Contents AssemblyAssembling the Steering Wheel Installing the SeatHow to Install the Battery Cables Maintenance Free BatteryHow To Check The Safety Interlock Switches Remove the protective cap from the battery terminalIMPORTANT! Before You Start Mowing Operator Presence System SeatHow to Prepare the Engine Check the TiresCheck the Level of the Mower Deck Features and Controls How to Use the Throttle Control Using ControlsOperation AttachmentsHow to Engage the Blades How to Use the Speed Control PedalDriving and Stopping the Unit How to Drive in Reverse How to Use the Cruise ControlHow to Change Direction How to Disconnect the TransmissionHow to Set the Parking Brake How to Change the Cutting HeightHow to Stop the Unit How to Operate the Mower Deck How to Transport the UnitRemove the key to restrict access to the RMO feature MowingHow to Stop on a Hill How to Operate the Unit on HillsHow to Start Operation on a Hill All-Wheel SteeringEngine Operation How to Start the EngineBefore Starting the Engine Check the Oil Add GasolineOperating Tips TipsMowing and Bagging Tips Use the left side of the mower deck to trim near an objectMaintenance Schedule MaintenanceFrequency Maintenance Required Comments Maintenance engine Examine bladesHow to Remove and Install the Blade How to Check the MufflerGeneral Recommendations InspectionHow to Sharpen the Blade Install the mower deck. See How To Install The Mower DeckAdjustments How to Check and Adjust the PTO ClutchBlade Brake Check Remove the 1/4 inch 6 mm pin or bolt Figure How to Check and Adjust the Motion Drive BeltAdjusting drive brake Drive brake Gearbox Hex nut How to Check and Adjust the Drive BrakeLift the battery tray and the battery out of the unit How to Remove the BatteryHow to Clean the Battery How to Charge the BatteryLubrication Where to LubricateHow to Check the Fuel Filter Mower Deck MaintenanceHow to Remove the Mower Deck How to Install the Mower DeckHanger rod Q Adjuster arm How to Level the Mower Deck How to Adjust the Gauge WheelsAxle bolts for the gauge wheels were mounted Remove the gauge wheels FigureReplacing the Motion Drive Belt Loosening adjuster knobs Lift link Adjuster knobsHow to Replace the Primary Mower Drive Belt How to Replace the Secondary Mower Drive BeltRemove the primary mower drive belt from the stack pulley English Rear wheel assembly Valve stem How to Install the WheelsRemove the bolt or pin used in step Wheel AlignmentHow to Replace the Light Bulb How to Replace the FuseHow to Clean the Mower Deck Raise the tractor hoodStorage over 30 days Troubleshooting Chart TroubleshootingCorrectly Pedal is depressed When the brake pedal isCut level Mower blades will notProduct Specifications SpecificationsEnglish Page English Page Year Limited Warranty Snapper Products Macon Street McDonough, GA

LT23460AWS specifications

The Snapper LT23460AWS is a versatile riding lawn mower designed for homeowners seeking efficiency, comfort, and ease of use in maintaining their lawns. This model comes equipped with several innovative features and technologies that enhance its performance and user experience.

One of the standout characteristics of the LT23460AWS is its powerful 23 horsepower Briggs & Stratton engine. This engine provides ample power to tackle various terrains, ensuring a smooth and efficient mowing experience. The mower operates on a hydrostatic transmission system, allowing users to easily adjust the speed and direction without the need for manual shifting, making it ideal for navigating around obstacles with ease.

The Snapper LT23460AWS features a 60-inch cutting deck, which allows for wide coverage in fewer passes, reducing the time spent mowing. This cutting deck is equipped with a robust cutting system, designed to deliver a clean, precise cut, whether tackling tall grass or maintaining a manicured lawn. Additionally, the deck height can be easily adjusted to suit different grass lengths, providing flexibility in lawn care.

Comfort is a key aspect of the LT23460AWS. The mower is designed with a spacious, ergonomic seat that provides ample cushioning, allowing for hours of comfortable mowing. Its easy-to-reach controls are strategically placed, enhancing user convenience and minimizing fatigue. The steering wheel is designed for optimal maneuverability, making it easier to navigate tight corners and complex landscaping.

Another notable technology in the Snapper LT23460AWS is the Advanced Air Management System. This technology optimizes airflow within the cutting deck, ensuring even grass distribution and improving overall cut quality. Moreover, the mower includes a mulching capability, allowing homeowners to cut grass into fine pieces that can enrich the lawn when returned to the soil.

The LT23460AWS is also designed with durability in mind. Its robust construction features high-quality materials that can withstand the rigors of regular mowing. This commitment to durability ensures that the Snapper LT23460AWS will provide reliable performance season after season.

In summary, the Snapper LT23460AWS is a powerful and efficient riding mower that combines advanced technology with user-friendly design. With its powerful engine, hydrostatic transmission, and comfortable seating, this mower is poised to meet the diverse needs of homeowners while delivering high-quality lawn care results.
Top Page Image Contents