Snapper LT23460AWS Engine Operation, Before Starting the Engine Check the Oil, Add Gasoline

Page 20

Engine Operation

Before Starting the Engine

Check the Oil

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer’s instructions for the type of gasoline and oil to use.

1.Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Check the oil. Follow the procedure in the engine manufacturer’s instructions.

3.If necessary, add oil until the oil reaches the FULL mark on the dipstick. The quantity of oil needed from ADD to FULL is shown on the dipstick. Do not add too much oil.

Add Gasoline

WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. Do not add gasoline when you are inside an enclosure. Before you add gasoline, stop the engine and let the engine cool for several minutes.

Fill the fuel tank with regular unleaded gasoline. Do not use premium unleaded gasoline. Make sure the gasoline is fresh and clean. Leaded gasoline will increase deposits and shorten the life of the valves.

A

B

Figure 17: Gas tank

A - Fuel tank

B - Full line

CAUTION: A mixture of alcohol (ethanol or methanol) and gasoline (called gasohol), will attract moisture and cause acid deposits during storage. While the unit is in storage, the acids in the fuel can damage the fuel system.

To prevent engine problems with the fuel system, empty the fuel system before storage of 30 days or longer as follows.

1.Drain the fuel tank.

2.Start the engine. Let the engine run until the fuel lines and the carburetor are empty.

3.After storage, make sure you use fresh fuel. See the storage instructions for additional information.

4.Never use engine cleaner or carburetor cleaner in the fuel tank or permanent damage can occur.

Carburetor

Do not attempt to adjust the carburator. Engine adjustments and repairs should be performed only by an authorized dealer.

How to Start the Engine

WARNING: The electrical system has an operator presence system that includes a sensor switch for the seat. These components tell the electrical system if the operator is sitting on the seat. This system will stop the engine when the operator leaves the seat. For your protection, always make sure this system operates correctly.

NOTE: The engine will not start unless you depress the brake pedal or engage the parking brake and disengage the blades.

1.Push the brake pedal completely forward. Keep your foot on the pedal.

2.Make sure the blades are disengaged.

3.Move the throttle control completely forward to the FAST position.

4.Move the choke control completely forward.

5.Turn the ignition key to the START position. Release the key when the engine starts.

NOTE: If the engine does not start after four or five tries, see the TROUBLESHOOTING CHART.

6.Turn off the choke, and slowly move the throttle control to the SLOW position.

7.Let a cold engine run for several minutes. Begin work when the engine is warm. To start a hot engine, move the throttle control to a position between FAST and SLOW.

20

www.snapper.com

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Lawn Tractor Series Manual No Rev. ‘-’, 2/18/2009Date Purchased Where to Find Us MowerEngine Table of Contents Protection for Children Protection against TipoversPreparation Do not allow pre-teenage children to operate machineSafe Handling of Gasoline OperationTowing International Pictorials GhijAssembly Parts Bag ContentsInstalling the Seat Assembling the Steering WheelMaintenance Free Battery How to Install the Battery CablesRemove the protective cap from the battery terminal How To Check The Safety Interlock SwitchesIMPORTANT! Before You Start Mowing Operator Presence System SeatCheck the Level of the Mower Deck How to Prepare the EngineCheck the Tires Features and Controls Using Controls How to Use the Throttle ControlOperation AttachmentsDriving and Stopping the Unit How to Engage the BladesHow to Use the Speed Control Pedal How to Use the Cruise Control How to Drive in ReverseHow to Change Direction How to Disconnect the TransmissionHow to Stop the Unit How to Set the Parking BrakeHow to Change the Cutting Height How to Transport the Unit How to Operate the Mower DeckRemove the key to restrict access to the RMO feature MowingHow to Operate the Unit on Hills How to Stop on a HillHow to Start Operation on a Hill All-Wheel SteeringHow to Start the Engine Engine OperationBefore Starting the Engine Check the Oil Add GasolineTips Operating TipsMowing and Bagging Tips Use the left side of the mower deck to trim near an objectMaintenance Maintenance ScheduleFrequency Maintenance Required Comments Maintenance engine Examine bladesHow to Check the Muffler How to Remove and Install the BladeGeneral Recommendations InspectionInstall the mower deck. See How To Install The Mower Deck How to Sharpen the BladeBlade Brake Check AdjustmentsHow to Check and Adjust the PTO Clutch How to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHow to Check and Adjust the Drive Brake Adjusting drive brake Drive brake Gearbox Hex nutHow to Remove the Battery Lift the battery tray and the battery out of the unitHow to Clean the Battery How to Charge the BatteryWhere to Lubricate LubricationMower Deck Maintenance How to Check the Fuel FilterHow to Remove the Mower Deck How to Install the Mower DeckHanger rod Q Adjuster arm How to Adjust the Gauge Wheels How to Level the Mower DeckAxle bolts for the gauge wheels were mounted Remove the gauge wheels FigureLoosening adjuster knobs Lift link Adjuster knobs Replacing the Motion Drive BeltRemove the primary mower drive belt from the stack pulley How to Replace the Primary Mower Drive BeltHow to Replace the Secondary Mower Drive Belt English How to Install the Wheels Rear wheel assembly Valve stemWheel Alignment Remove the bolt or pin used in stepHow to Replace the Fuse How to Replace the Light BulbHow to Clean the Mower Deck Raise the tractor hoodStorage over 30 days Troubleshooting Troubleshooting ChartPedal is depressed When the brake pedal is CorrectlyCut level Mower blades will notSpecifications Product SpecificationsEnglish Page English Page Year Limited Warranty Snapper Products Macon Street McDonough, GA

LT23460AWS specifications

The Snapper LT23460AWS is a versatile riding lawn mower designed for homeowners seeking efficiency, comfort, and ease of use in maintaining their lawns. This model comes equipped with several innovative features and technologies that enhance its performance and user experience.

One of the standout characteristics of the LT23460AWS is its powerful 23 horsepower Briggs & Stratton engine. This engine provides ample power to tackle various terrains, ensuring a smooth and efficient mowing experience. The mower operates on a hydrostatic transmission system, allowing users to easily adjust the speed and direction without the need for manual shifting, making it ideal for navigating around obstacles with ease.

The Snapper LT23460AWS features a 60-inch cutting deck, which allows for wide coverage in fewer passes, reducing the time spent mowing. This cutting deck is equipped with a robust cutting system, designed to deliver a clean, precise cut, whether tackling tall grass or maintaining a manicured lawn. Additionally, the deck height can be easily adjusted to suit different grass lengths, providing flexibility in lawn care.

Comfort is a key aspect of the LT23460AWS. The mower is designed with a spacious, ergonomic seat that provides ample cushioning, allowing for hours of comfortable mowing. Its easy-to-reach controls are strategically placed, enhancing user convenience and minimizing fatigue. The steering wheel is designed for optimal maneuverability, making it easier to navigate tight corners and complex landscaping.

Another notable technology in the Snapper LT23460AWS is the Advanced Air Management System. This technology optimizes airflow within the cutting deck, ensuring even grass distribution and improving overall cut quality. Moreover, the mower includes a mulching capability, allowing homeowners to cut grass into fine pieces that can enrich the lawn when returned to the soil.

The LT23460AWS is also designed with durability in mind. Its robust construction features high-quality materials that can withstand the rigors of regular mowing. This commitment to durability ensures that the Snapper LT23460AWS will provide reliable performance season after season.

In summary, the Snapper LT23460AWS is a powerful and efficient riding mower that combines advanced technology with user-friendly design. With its powerful engine, hydrostatic transmission, and comfortable seating, this mower is poised to meet the diverse needs of homeowners while delivering high-quality lawn care results.
Top Page Image Contents