Snapper LT23460AWS How to Use the Cruise Control, Push the brake pedal, How to Drive in Reverse

Page 16

How to Use the Cruise Control

To engage the cruise control:

1.Slowly push the speed control pedal forward to the desired speed (Figure 11).

2.Pull up on the cruise control knob (Figure 12). Release the speed control pedal. The unit should continue traveling forward at the desired speed.

NOTE: The cruise control only operates in forward speeds.

To disengage the cruise control:

1.Push the speed control pedal (Figure 11), OR

2.Push the brake pedal.

WARNING: Do not engage the cruise control when driving on slopes, or when people or animals are in the vicinity.

A

Figure 12: Cruise control

A - Cruise Control knob

How to Drive in Reverse

1.Look to the rear.

2.Slowly push the speed control pedal to the REVERSE position.

How to Change Direction

CAUTION: To change directions, do not use the left brake pedal. Use only the speed control pedal.

1.Slowly remove your foot from the speed control pedal. The speed control pedal will automatically return to the NEUTRAL position.

2.When the unit stops, slowly move the speed control pedal to the desired direction.

Speed Control Pedal Positions

The forward speed is controlled by the position of the speed control pedal. The following chart provides functions along with the pedal positions. Always operate the engine with the throttle control in the FAST position.

Function

Pedal Positon

Throttle Position

 

 

 

Trimming

1/3

Fast Throttle

Snow Thrower

 

 

Bagging Grass

1/3 to 1/2

 

 

 

 

Normal Mowing

1/2 to 2/3

 

 

 

 

Easy Mowing

1/2 to 3/4

 

Snow Blade

 

 

 

Transport

FULL

 

 

 

 

Pull Behind

1/3 to 1/2

 

Attachments

 

 

 

How to Disconnect the Transmission

To push the unit, use the automatic drive disconnect to release the transmission. The automatic drive disconnect is located under the seat.

1.The engine must be off.

2.Raise the seat. The automatic drive disconnect is under the seat.

3.Move and latch the automatic drive disconnect in the PUSH position (Figure 13). The transmission is now released and the unit can be pushed.

NOTE: In cold weather, the heavy viscosity oil in the transmission will make the unit difficult to push.

4.To engage the transmission, unlatch the automatic drive disconnect. The transmission is now connected and ready to operate.

16

www.snapper.com

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Lawn Tractor Series Manual No Rev. ‘-’, 2/18/2009Engine Where to Find Us MowerDate Purchased Table of Contents Protection for Children Protection against TipoversPreparation Do not allow pre-teenage children to operate machineSafe Handling of Gasoline OperationTowing International Pictorials GhijAssembly Parts Bag ContentsInstalling the Seat Assembling the Steering WheelMaintenance Free Battery How to Install the Battery CablesRemove the protective cap from the battery terminal How To Check The Safety Interlock SwitchesIMPORTANT! Before You Start Mowing Operator Presence System SeatCheck the Tires How to Prepare the EngineCheck the Level of the Mower Deck Features and Controls Using Controls How to Use the Throttle ControlOperation AttachmentsHow to Use the Speed Control Pedal How to Engage the BladesDriving and Stopping the Unit How to Use the Cruise Control How to Drive in ReverseHow to Change Direction How to Disconnect the TransmissionHow to Change the Cutting Height How to Set the Parking BrakeHow to Stop the Unit How to Transport the Unit How to Operate the Mower DeckRemove the key to restrict access to the RMO feature MowingHow to Operate the Unit on Hills How to Stop on a HillHow to Start Operation on a Hill All-Wheel SteeringHow to Start the Engine Engine OperationBefore Starting the Engine Check the Oil Add GasolineTips Operating TipsMowing and Bagging Tips Use the left side of the mower deck to trim near an objectMaintenance Maintenance ScheduleFrequency Maintenance Required Comments Maintenance engine Examine bladesHow to Check the Muffler How to Remove and Install the BladeGeneral Recommendations InspectionInstall the mower deck. See How To Install The Mower Deck How to Sharpen the BladeHow to Check and Adjust the PTO Clutch AdjustmentsBlade Brake Check How to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHow to Check and Adjust the Drive Brake Adjusting drive brake Drive brake Gearbox Hex nutHow to Remove the Battery Lift the battery tray and the battery out of the unitHow to Clean the Battery How to Charge the BatteryWhere to Lubricate LubricationMower Deck Maintenance How to Check the Fuel FilterHow to Remove the Mower Deck How to Install the Mower DeckHanger rod Q Adjuster arm How to Adjust the Gauge Wheels How to Level the Mower DeckAxle bolts for the gauge wheels were mounted Remove the gauge wheels FigureLoosening adjuster knobs Lift link Adjuster knobs Replacing the Motion Drive BeltHow to Replace the Secondary Mower Drive Belt How to Replace the Primary Mower Drive BeltRemove the primary mower drive belt from the stack pulley English How to Install the Wheels Rear wheel assembly Valve stemWheel Alignment Remove the bolt or pin used in stepHow to Replace the Fuse How to Replace the Light BulbHow to Clean the Mower Deck Raise the tractor hoodStorage over 30 days Troubleshooting Troubleshooting ChartPedal is depressed When the brake pedal is CorrectlyCut level Mower blades will notSpecifications Product SpecificationsEnglish Page English Page Year Limited Warranty Snapper Products Macon Street McDonough, GA

LT23460AWS specifications

The Snapper LT23460AWS is a versatile riding lawn mower designed for homeowners seeking efficiency, comfort, and ease of use in maintaining their lawns. This model comes equipped with several innovative features and technologies that enhance its performance and user experience.

One of the standout characteristics of the LT23460AWS is its powerful 23 horsepower Briggs & Stratton engine. This engine provides ample power to tackle various terrains, ensuring a smooth and efficient mowing experience. The mower operates on a hydrostatic transmission system, allowing users to easily adjust the speed and direction without the need for manual shifting, making it ideal for navigating around obstacles with ease.

The Snapper LT23460AWS features a 60-inch cutting deck, which allows for wide coverage in fewer passes, reducing the time spent mowing. This cutting deck is equipped with a robust cutting system, designed to deliver a clean, precise cut, whether tackling tall grass or maintaining a manicured lawn. Additionally, the deck height can be easily adjusted to suit different grass lengths, providing flexibility in lawn care.

Comfort is a key aspect of the LT23460AWS. The mower is designed with a spacious, ergonomic seat that provides ample cushioning, allowing for hours of comfortable mowing. Its easy-to-reach controls are strategically placed, enhancing user convenience and minimizing fatigue. The steering wheel is designed for optimal maneuverability, making it easier to navigate tight corners and complex landscaping.

Another notable technology in the Snapper LT23460AWS is the Advanced Air Management System. This technology optimizes airflow within the cutting deck, ensuring even grass distribution and improving overall cut quality. Moreover, the mower includes a mulching capability, allowing homeowners to cut grass into fine pieces that can enrich the lawn when returned to the soil.

The LT23460AWS is also designed with durability in mind. Its robust construction features high-quality materials that can withstand the rigors of regular mowing. This commitment to durability ensures that the Snapper LT23460AWS will provide reliable performance season after season.

In summary, the Snapper LT23460AWS is a powerful and efficient riding mower that combines advanced technology with user-friendly design. With its powerful engine, hydrostatic transmission, and comfortable seating, this mower is poised to meet the diverse needs of homeowners while delivering high-quality lawn care results.
Top Page Image Contents