Snapper 150Z Series manual General Operating Safety

Page 11

Choke

CLOSE the choke for cold starting (pull knob up). OPEN the choke once the engine starts (push knob down). If the engine is warm, it may not require choking. If this is the case, set the choke to OPEN (push the knob down) while cranking the engine. In most cases, you will need to close the choke in order to start the engine.

Mower Cutting Height Switch

To increase the mower cutting height (raise the mower deck), press the top of the yellow cutting height switch. To decrease mower cutting height (lower the mower deck), press the bottom of the switch. Mower cutting height range is approximately 3-3/4” to 1-1/2”. The cutting height gauge indicates the position of the mower deck. The cutting height gauge is located on the front of the rider, just behind the driver’s left leg.

Ignition Switch

The ignition switch starts and stops the engine; it has three positions:

OFF Stops the engine and shuts off the electrical system.

RUN Allows the engine to run and powers the electrical system.

START Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN position with the engine stopped. This drains the battery.

Hour Meter

The hour meter measures the number of hours the key has been in the RUN position.

NOTE: The hour meter will register the passage of time when the key is in the RUN position, even if the engine is not running.

Mower Blade Switch

The yellow mower blade switch turns the mower blades on and off. To turn the mower blades ON, pull the switch up. To turn the mower blades OFF, push the switch down. Always set the engine speed control to FAST before turning the mower blades ON, and while mowing.

Transmission Release Levers

The transmission release levers deactivate the transmissions so that the unit can be pushed by hand. See PUSHING THE UNIT BY HAND for operational information.

Fuel Tank

To remove the fuel tank cap, turn it counterclockwise.

GENERAL OPERATING SAFETY

Before first time operation:

•Be sure to read all information in the Safety and Operation sections before attempting to operate this rider and mower.

•Become familiar with all of the controls and how to stop the unit.

•Drive in an open area without mowing to become accustomed to driving the unit.

WARNING

If you do not understand how a specific control functions, or have not yet thoroughly read the CONTROL FUNCTIONS section, do so now.

Do NOT attempt to operate the rider without first becoming familiar with the location and function of ALL controls.

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 18.5, 21, 24, 26HP Zero-Turn Riders OPERATOR’S ManualPage Table of Contents General Operation Safety RulesIgnition System Suggested Guide for Sighting Slopes for Safe Operation Safe Handling of Gasoline Service & MaintenanceDecal Amputation Thrown Objects Hazard Decks Safety & Operation DecalsID Tag Identification NumbersParking Brake Lever OperationControl Functions Ground Speed LeversGeneral Operating Safety Fuel Recommendations Checks Before StartingPushing the Rider by Hand Emergency StoppingStopping the Rider & Engine Starting the EngineReverse Travel Practice Driving PracticeSmooth Travel Forward Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsRemoving the Mower Deck Installing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks 18.5, 21HP Briggs & Stratton MaintenanceMaintenance Schedule Rider MAINTENANCE, All ModelsCheck Tire Pressure Accessing the Engine CompartmentClean Debris from Rider Engine Compartment Clean Debris from Engine Cooling Areas and AIR FilterOil LubricationGrease Lubricating Mower Lift Blade Removal 33 Deck Clean Deck Check / Replace Mower BladesPage Operational Safety Checks Clean the Battery and CablesCheck Rider Safety System Adjust PTO Clutch Window Adjustment Nut Feeler Gauge Check / Adjust PTO ClutchChange Engine OIL & Filter Check Engine OIL LevelChange Engine OIL Air Filter Removal & Installation Service AIR Filter & PRE-CLEANER 18.5 & 21 HP EnginesAir Filter Cover Air Filter Cover Screws Service AIR Filter 24 & 26HP EnginesReplace Spark Plug Clean Combustion Chamber Briggs & Stratton ModelsPre-Cleaner Service Air Filter Service Pre-CleanerCutting Height Adjustment Service & AdjustmentsGround Speed Control Lever Adjustment Speed Balancing Adjustment62cm Brake AdjustmentBattery Charging Engine AdjustmentsSide to Side Leveling 33 Decks Mower Deck Leveling AdjustmentsSide to Side Leveling 42 & 50 Decks Orient Blades Front-to-Back Front To Back Leveling 33 DeckDeck Front To Back Leveling 42 & 50 DecksMower Drive Belt Replacement 42 Decks Mower Belt ReplacementMower Drive Belt Replacement 33 Decks Storage StorageTroubleshooting the Rider TroubleshootingTroubleshooting the Mower Specifications Replacement Parts Service ItemsHOW High to MOW the Grass HOW and When toWATER, Fertilize AerateProper Mowing Speed When and HOW Often to MOW

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.
Top Page Image Contents