Snapper Comprehensive Troubleshooting for Lawn Mowers

Page 38

TROUBLESHOOTING

While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies.

If you prefer, all of these procedures can be performed by your local authorized dealer.

WARNING

To avoid serious injury, perform maintenance on the rider or mower only when the engine is stopped, the ground speed levers are set to START/PARK, and the parking brake lever is set to

ENGAGE.

Always remove the ignition key, disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine.

Troubleshooting the Rider

PROBLEM

CAUSE

REMEDY

 

 

 

Engine will

Ignition switch not turned fully to START position.

Turn ignition switch fully to START position.

not turnover.

 

 

Ground speed levers not set to START/PARK.

Set to START/PARK.

 

 

 

 

Mower blade switch in ON position.

Place in OFF position.

 

 

 

 

Parking brake lever in DISENGAGE position.

Set to ENGAGE position.

 

 

 

 

Battery terminals require cleaning.

Clean the battery terminals

 

 

 

 

Battery discharged or dead.

Recharge or replace.

 

 

 

 

Wiring loose or broken; connector separated.

Visually check wiring & replace broken or frayed

 

 

wires. Tighten loose connections.

 

 

 

 

Safety interlock switch faulty.

Replace. Contact your local authorized dealer.

 

 

 

 

Solenoid or starter motor faulty.

Replace. Contact your local authorized dealer.

 

 

 

Engine will

Engine is cold; choke not in CLOSED position.

Move choke to CLOSED position.

turnover but

 

 

Engine is warm; choke not in OPEN position.

Move choke to OPEN position.

will not start.

 

 

Engine flooded.

Set choke to OPEN position when cranking engine.

 

 

 

 

 

Out of fuel.

Allow engine to cool, then refill the fuel tank.

 

 

 

 

Fuel is old or stale, or water in fuel.

Drain fuel & replace with fresh fuel. Contact your

 

 

local authorized dealer.

 

 

 

 

Spark plug(s) faulty, fouled or incorrectly gapped.

Clean and gap or replace.

 

 

 

 

Safety interlock switch faulty.

Replace. Contact your local authorized dealer.

 

 

 

Engine starts

Air filter plugged

Service pre-cleaner and/or replace air filter

hard or runs

 

element.

poorly.

 

 

Choke not set to CLOSED position when

Set choke to CLOSED when cranking. Set choke

 

 

cranking the engine, OR choke not set to OPEN

to OPEN when engine is running. A warm engine

 

after engine starts.

may not require choking.

 

 

 

 

Spark plug faulty, fouled, or incorrectly gapped.

Clean and gap or replace.

 

 

 

Engine

Low oil level.

Check/add oil as required.

knocks.

 

 

Using wrong grade oil.

See "Change Engine Oil" in the Maintenance

 

 

Section.

 

 

 

Excessive oil

Engine running too hot.

Clean engine cooling fins, blower screen and air

consumption.

 

cleaner.

 

 

 

 

Using wrong weight oil.

See "Change Engine Oil" in the Maintenance

 

 

Section.

 

 

 

 

Too much oil in crankcase.

Drain excess oil.

 

 

 

Engine

Dirty air filter or pre-cleaner, or both.

Service or replace as required. See Maintenance

exhaust is

 

Section.

black.

 

 

Choke set to CLOSED when engine is running.

Set choke to OPEN as soon as engine starts.

 

 

 

36

Image 38
Contents OPERATOR’S Manual 18.5, 21, 24, 26HP Zero-Turn RidersPage Table of Contents Safety Rules General OperationIgnition System Suggested Guide for Sighting Slopes for Safe Operation Service & Maintenance Safe Handling of GasolineSafety & Operation Decals Decal Amputation Thrown Objects Hazard DecksIdentification Numbers ID TagGround Speed Levers OperationControl Functions Parking Brake LeverGeneral Operating Safety Checks Before Starting Fuel RecommendationsStarting the Engine Emergency StoppingStopping the Rider & Engine Pushing the Rider by HandForward Travel Practice Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnInstalling the Mower Deck Removing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Rider MAINTENANCE, All Models MaintenanceMaintenance Schedule 18.5, 21HP Briggs & StrattonClean Debris from Engine Cooling Areas and AIR Filter Accessing the Engine CompartmentClean Debris from Rider Engine Compartment Check Tire PressureOil LubricationGrease Lubricating Mower Lift Clean Deck Check / Replace Mower Blades Blade Removal 33 DeckPage Operational Safety Checks Clean the Battery and CablesCheck Rider Safety System Check / Adjust PTO Clutch Adjust PTO Clutch Window Adjustment Nut Feeler GaugeChange Engine OIL & Filter Check Engine OIL LevelChange Engine OIL Service AIR Filter & PRE-CLEANER 18.5 & 21 HP Engines Air Filter Removal & InstallationService AIR Filter 24 & 26HP Engines Air Filter Cover Air Filter Cover ScrewsAir Filter Service Pre-Cleaner Clean Combustion Chamber Briggs & Stratton ModelsPre-Cleaner Service Replace Spark PlugSpeed Balancing Adjustment Service & AdjustmentsGround Speed Control Lever Adjustment Cutting Height AdjustmentEngine Adjustments Brake AdjustmentBattery Charging 62cmMower Deck Leveling Adjustments Side to Side Leveling 33 DecksSide to Side Leveling 42 & 50 Decks Front To Back Leveling 33 Deck Orient Blades Front-to-BackFront To Back Leveling 42 & 50 Decks DeckMower Drive Belt Replacement 42 Decks Mower Belt ReplacementMower Drive Belt Replacement 33 Decks Storage StorageTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Specifications Service Items Replacement PartsAerate HOW and When toWATER, Fertilize HOW High to MOW the GrassWhen and HOW Often to MOW Proper Mowing Speed

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.