Snapper 150Z Series manual Check Engine OIL Level, Change Engine OIL & Filter

Page 26

Engine Maintenance Items

CHECK ENGINE OIL LEVEL

Service Interval: Before each use, and every 8 hours.

1.Turn the engine off, and set the parking brake lever to

ENGAGE.

2.Clean the area around the dip stick (C, Figure 34).

3.Remove the dip stick (C) and clean it with a paper towel.

4.Insert the dip stick back into the engine. Thread the cap back into the tube (D).

5.Remove the dip stick and read the oil level. The oil level should be between the “FULL” and “ADD” marks

(D). If not, add oil according to the oil recommendations chart (Figure 33).

CHANGE ENGINE OIL

Service Interval: 50 hours or once per season.

NOTE: Change engine oil while the engine is warm. Run the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 34) and oil drain tube (A).

2.Remove the oil drain plug (A) from the end of the oil drain tube. Remove the dip stick (C). Allow ample time for complete drainage.

3.Reinstall the oil drain plug (A) and route the hose next to the engine.

4.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL above.

5.Start and run the engine at SLOW speed for 30 seconds. Stop the engine and recheck the oil level.

CHANGE ENGINE OIL & FILTER

Service Interval: 100 hours or once per season.

NOTE: Change engine oil while the engine is warm. Run the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 34) and oil drain (A).

2.Remove the oil drain plug (A) and dip stick (C). Allow ample time for complete drainage.

3.Remove the oil filter (B). Discard the filter.

4.Using a drop of oil on your finger tip, wet the rubber gasket on the bottom of the new filter.

5.Turn the filter clockwise until the rubber gasket meets the filter base. Then turn 1/2 to 3/4 turn more.

Use oil classified API Service Class SF, SG, SH, SJ or better with SAE Viscosity:

 

 

 

 

 

 

30 Conventional**

 

 

 

 

5W-30

 

 

 

 

 

 

 

10W-30

 

 

 

 

 

 

Conventional*

 

 

 

 

 

 

Synthetic 5W-30, 10W-30

 

 

˚F

-20

0

20

32

40

60

80

100

˚C

-30

-18

-7

0

4

16

27

38

*CAUTION: Air cooled engines run hotter than automotive engines.

 

The use of non-synthetic multi-viscosity oils (5W-30, 10W-30, etc.)

 

in temperatures above 40º F (4ºC) will result in higher than normal

 

oil consumption. When using a multi-viscosity oil, check oil level

 

more frequently.

 

 

 

 

 

 

**CAUTION: SAE 30 oil, if used below 40º F (4ºC), will result in hard starting and possible engine bore damage due to inadequate lubrication.

Figure 33. Recommended Engine Oil -

Briggs & Stratton Models

D

B

A

C

Figure 34. Oil Change - Briggs & Stratton Models

A.Oil Drain Tube

B.Oil Filter

C.Dip Stick

D.Checking Oil Level

6.Reinstall the oil drain plug (A).

7.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL above.

8.Start and run the engine at SLOW speed for 30 seconds. Stop the engine and recheck the oil level.

9.Test run the engine to check for leaks. Stop the engine for 1 minute, then recheck the oil level.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents OPERATOR’S Manual 18.5, 21, 24, 26HP Zero-Turn RidersPage Table of Contents Safety Rules General OperationIgnition System Suggested Guide for Sighting Slopes for Safe Operation Service & Maintenance Safe Handling of GasolineSafety & Operation Decals Decal Amputation Thrown Objects Hazard DecksIdentification Numbers ID TagGround Speed Levers OperationControl Functions Parking Brake LeverGeneral Operating Safety Checks Before Starting Fuel RecommendationsStarting the Engine Emergency StoppingStopping the Rider & Engine Pushing the Rider by HandForward Travel Practice Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnInstalling the Mower Deck Removing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Rider MAINTENANCE, All Models MaintenanceMaintenance Schedule 18.5, 21HP Briggs & StrattonClean Debris from Engine Cooling Areas and AIR Filter Accessing the Engine CompartmentClean Debris from Rider Engine Compartment Check Tire PressureOil LubricationGrease Lubricating Mower Lift Clean Deck Check / Replace Mower Blades Blade Removal 33 DeckPage Operational Safety Checks Clean the Battery and CablesCheck Rider Safety System Check / Adjust PTO Clutch Adjust PTO Clutch Window Adjustment Nut Feeler GaugeChange Engine OIL & Filter Check Engine OIL LevelChange Engine OIL Service AIR Filter & PRE-CLEANER 18.5 & 21 HP Engines Air Filter Removal & InstallationService AIR Filter 24 & 26HP Engines Air Filter Cover Air Filter Cover ScrewsAir Filter Service Pre-Cleaner Clean Combustion Chamber Briggs & Stratton ModelsPre-Cleaner Service Replace Spark PlugSpeed Balancing Adjustment Service & AdjustmentsGround Speed Control Lever Adjustment Cutting Height AdjustmentEngine Adjustments Brake AdjustmentBattery Charging 62cmMower Deck Leveling Adjustments Side to Side Leveling 33 DecksSide to Side Leveling 42 & 50 Decks Front To Back Leveling 33 Deck Orient Blades Front-to-BackFront To Back Leveling 42 & 50 Decks DeckMower Drive Belt Replacement 42 Decks Mower Belt ReplacementMower Drive Belt Replacement 33 Decks Storage StorageTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Specifications Service Items Replacement PartsAerate HOW and When toWATER, Fertilize HOW High to MOW the GrassWhen and HOW Often to MOW Proper Mowing Speed

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.
Top Page Image Contents