Snapper 150Z Series Emergency Stopping, Stopping the Rider & Engine, Starting the Engine, Mowing

Page 13

EMERGENCY STOPPING

In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine shut down follow the procedure given in STOPPING THE RIDER AND ENGINE.

STOPPING THE RIDER & ENGINE

1.Return the ground speed control levers to START/PARK positions to stop rider movement.

2.Engage the parking brake.

3.Turn off the mower blades by pushing the mower blade switch down to the OFF position.

4.Move the engine speed control to SLOW position and turn the ignition switch to OFF. Remove the key.

STARTING THE ENGINE

1.While sitting in the seat, make sure the mower blade switch is OFF, the ground speed control levers are locked in START/PARK positions, and the parking brake is engaged.

2.Move the engine speed control fully forward to FAST. Set the choke control to CLOSED (pull knob UP).

NOTE: A warm engine may not require choking. In this case, set the choke control to OPEN (push knob down).

3.Insert the key into the ignition switch and turn it to START to crank the engine.

4.After the engine starts, release the key. It will return to the RUN position. Gradually push the choke knob down to OPEN position. Warm the engine by running it for at least a minute before turning on the mower blades, or driving the unit.

ALWAYS operate the unit with the engine speed control set to FAST when mowing or driving. NEVER engage the mower blades with the engine speed set to SLOW.

9.Stop the rider and engine (see STOPPING THE RIDER AND ENGINE).

PUSHING THE RIDER BY HAND

NOTE: Do not disengage the transmissions if parked on

aslope.

1.Turn the mower blades OFF, push the ground speed control levers out to their START/PARK positions, engage the parking brake, turn the ignition switch OFF, remove the key, and wait for all moving parts to stop.

2.Locate the transmission release levers (C, Figure 3) at the rear of the unit.

3.Pull both levers back and down to release the transmissions (position B, Figure 3).

4.Pull the ground speed control levers in to their DRIVE positions, and disengage the parking brake.

The rider can now be pushed by hand.

5.After moving the rider, set the ground speed control levers to START/PARK, engage the parking brake, and push both transmission release levers forward to re-engage the transmissions (position A, Figure 3).

DO NOT TOW RIDER

Towing the unit will cause transmission damage. Do not use another vehicle to push or pull this unit. Do not use this unit to push or pull another vehicle or object.

A

MOWING

1.Start the engine (see STARTING THE ENGINE).

2.Set the mower cutting height to the desired setting using the mower cutting height switch.

3.Set the engine speed control to FAST.

4.Turn the mower blades ON (pull switch up).

5.Disengage the parking brake.

6.Move the ground speed control levers in from START/PARK positions to drive positions (levers in across the operator’s lap).

7.Begin mowing. See DRIVING PRACTICE.

8.When finished, turn the mower blades OFF (push switch down).

B

C

Figure 3. Transmission Release Levers

A.Drive Position

B.Push Position

C.Transmission Release Levers

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 18.5, 21, 24, 26HP Zero-Turn Riders OPERATOR’S ManualPage Table of Contents General Operation Safety RulesIgnition System Suggested Guide for Sighting Slopes for Safe Operation Safe Handling of Gasoline Service & MaintenanceDecal Amputation Thrown Objects Hazard Decks Safety & Operation DecalsID Tag Identification NumbersControl Functions OperationGround Speed Levers Parking Brake LeverGeneral Operating Safety Fuel Recommendations Checks Before StartingStopping the Rider & Engine Emergency StoppingStarting the Engine Pushing the Rider by HandSmooth Travel Driving PracticeForward Travel Practice Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting Turns Executing an End-Of-Row Zero TurnRemoving the Mower Deck Installing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Maintenance Schedule MaintenanceRider MAINTENANCE, All Models 18.5, 21HP Briggs & StrattonClean Debris from Rider Engine Compartment Accessing the Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Check Tire PressureGrease LubricationOil Lubricating Mower Lift Blade Removal 33 Deck Clean Deck Check / Replace Mower BladesPage Check Rider Safety System Clean the Battery and CablesOperational Safety Checks Adjust PTO Clutch Window Adjustment Nut Feeler Gauge Check / Adjust PTO ClutchChange Engine OIL Check Engine OIL LevelChange Engine OIL & Filter Air Filter Removal & Installation Service AIR Filter & PRE-CLEANER 18.5 & 21 HP EnginesAir Filter Cover Air Filter Cover Screws Service AIR Filter 24 & 26HP EnginesPre-Cleaner Service Clean Combustion Chamber Briggs & Stratton ModelsAir Filter Service Pre-Cleaner Replace Spark PlugGround Speed Control Lever Adjustment Service & AdjustmentsSpeed Balancing Adjustment Cutting Height AdjustmentBattery Charging Brake AdjustmentEngine Adjustments 62cmSide to Side Leveling 33 Decks Mower Deck Leveling AdjustmentsSide to Side Leveling 42 & 50 Decks Orient Blades Front-to-Back Front To Back Leveling 33 DeckDeck Front To Back Leveling 42 & 50 DecksMower Drive Belt Replacement 33 Decks Mower Belt ReplacementMower Drive Belt Replacement 42 Decks Storage StorageTroubleshooting the Rider TroubleshootingTroubleshooting the Mower Specifications Replacement Parts Service ItemsWATER, Fertilize HOW and When toAerate HOW High to MOW the GrassProper Mowing Speed When and HOW Often to MOW

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.
Top Page Image Contents