Snapper 150Z Series manual Service & Adjustments, Ground Speed Control Lever Adjustment

Page 30

SERVICE & ADJUSTMENTS

GROUND SPEED CONTROL LEVER ADJUSTMENT

The control levers have three adjustments:

To Adjust Control Lever Height: Pull the levers in across the operator’s lap to their DRIVE positions. Loosen the mount bolts (D, Figure 42) and raise or lower the levers to the desired position. Tighten the mounting bolts.(D).

To Adjust Control Lever End Gap: The control lever end gap (C, Figure 43) should be adjusted so that the levers do not contact each other when placed in DRIVE positions. Loosen the jam nut (A, Figure 42) and adjust the length of the carriage bolt (B) so that the levers do not contact each other. Repeat on the opposite side. Tighten the jam nut (A) to lock the carriage bolt in position.

To Adjust Operator Clearance: The space between the operator and the control levers can be increase by removing the lower mounting bolt (D, Figure 42), pivoting the lever forward, and reinstalling the capscrew through the control lever and forward slot (C). Repeat with the other ground speed lever.

C

A

D

B

E

Figure 42. Control Lever Adjustment

A.Jam Nut

B.Carriage Bolt

C.Forward Slot

D.Mount Bolts

E.Knob

SPEED BALANCING ADJUSTMENT

If the rider veers to the right or left when the ground

 

 

speed control levers are in the maximum forward

 

 

position, the top speed of the right lever can be balanced

 

 

by turning the adjustment knob (E, Figure 42). Loosen

 

 

the jam nut and turn the knob COUNTERCLOCKWISE

C

to increase speed or CLOCKWISE to decrease speed.

 

 

Tighten the jam nut when complete.

 

 

 

 

 

 

 

 

CUTTING HEIGHT ADJUSTMENT

 

A

 

 

 

 

To increase the mower cutting height (raise the mower

 

 

 

deck), press the top of the mower cutting height switch

 

Cutting

 

 

Height

 

(A, Figure 43) To decrease mower cutting height (lower

 

 

 

the mower deck), press the bottom of the switch. Mower

B

4

Hig

 

hCut

23

 

cutting height range is 3-3/4” to 1-1/2”. The cutting height

 

1

 

 

LowCut

 

 

 

gauge indicates the position of the mower deck.. The cutting height gauge (B) is located on the front of the rider, just behind the driver’s left leg.

PTO CLUTCH ADJUSTMENT

See CHECK / ADJUST PTO CLUTCH in the

Maintenance Section.

Figure 43. Cutting Height Adjustment

A. Cutting Height Adjustment Switch

B. Cutting Height Gauge

C. Control Lever End Gap

28

Image 30
Contents OPERATOR’S Manual 18.5, 21, 24, 26HP Zero-Turn RidersPage Table of Contents Safety Rules General OperationIgnition System Suggested Guide for Sighting Slopes for Safe Operation Service & Maintenance Safe Handling of GasolineSafety & Operation Decals Decal Amputation Thrown Objects Hazard DecksIdentification Numbers ID TagGround Speed Levers OperationControl Functions Parking Brake LeverGeneral Operating Safety Checks Before Starting Fuel RecommendationsStarting the Engine Emergency StoppingStopping the Rider & Engine Pushing the Rider by HandForward Travel Practice Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnInstalling the Mower Deck Removing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Rider MAINTENANCE, All Models MaintenanceMaintenance Schedule 18.5, 21HP Briggs & StrattonClean Debris from Engine Cooling Areas and AIR Filter Accessing the Engine CompartmentClean Debris from Rider Engine Compartment Check Tire PressureLubrication GreaseOil Lubricating Mower Lift Clean Deck Check / Replace Mower Blades Blade Removal 33 DeckPage Clean the Battery and Cables Check Rider Safety SystemOperational Safety Checks Check / Adjust PTO Clutch Adjust PTO Clutch Window Adjustment Nut Feeler GaugeCheck Engine OIL Level Change Engine OILChange Engine OIL & Filter Service AIR Filter & PRE-CLEANER 18.5 & 21 HP Engines Air Filter Removal & InstallationService AIR Filter 24 & 26HP Engines Air Filter Cover Air Filter Cover ScrewsAir Filter Service Pre-Cleaner Clean Combustion Chamber Briggs & Stratton ModelsPre-Cleaner Service Replace Spark PlugSpeed Balancing Adjustment Service & AdjustmentsGround Speed Control Lever Adjustment Cutting Height AdjustmentEngine Adjustments Brake AdjustmentBattery Charging 62cmMower Deck Leveling Adjustments Side to Side Leveling 33 DecksSide to Side Leveling 42 & 50 Decks Front To Back Leveling 33 Deck Orient Blades Front-to-BackFront To Back Leveling 42 & 50 Decks DeckMower Belt Replacement Mower Drive Belt Replacement 33 DecksMower Drive Belt Replacement 42 Decks Storage StorageTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Specifications Service Items Replacement PartsAerate HOW and When toWATER, Fertilize HOW High to MOW the GrassWhen and HOW Often to MOW Proper Mowing Speed

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.