Snapper 150Z Series manual Mower Deck Removal & Installation 42 & 50 Decks

Page 17

MOWER DECK REMOVAL & INSTALLATION - 42” & 50” DECKS

A

B C

NOTE: Perform mower removal and installation on a hard, level surface such as a concrete floor.

WARNING

After lowering the mower cutting height, engage parking brake, turn off the mower blades, turn the ignition switch to STOP, and remove key before attempting to install or remove the mower.

Removing the Mower Deck

1.Turn the mower blades OFF, put the ground speed control levers in START/PARK position, engage the parking brake, turn the ignition OFF, and wait for all moving parts to stop.

2.Pivot the front wheels forward.

3.Use the mower belt release lever (D, Figure 13) to release belt tension. Remove the mower belt (B) from engine pulley (A).

4.Turn the ignition switch from OFF to RUN without starting the engine.

5.Use the mower cutting height switch to raise the mower deck.

6.Place 4x4 wood blocks (D, Figure 12) under the front and rear lip of the mower deck to securely support it.

7.Use the mower cutting height switch to fully lower the mower so that is it resting on the 4x4 wood blocks.

8.Turn the ignition switch to OFF and remove the key.

9.Remove the hair pin clip (A) securing the rear mower lift arm. Separate the lift arm from the mower deck. Repeat on both sides of the mower.

10.Remove the hitch rod (C) from the hitch bracket.

11.Slide the mower deck out from under the rider.

Installing the Mower Deck

1.Slide the mower deck under the right side of the rider. Slide the mower forward and hook the front hitch rod (C, Figure 12) to the front mower deck hooks.

2.Slide the mower deck backwards and connect the rear lift arms to the mower deck. Secure with hair pin clips (A).

3.Insert the key into the ignition switch. Turn the switch from OFF to RUN without starting the engine.

4.Use the cutting height switch to raise the mower until it is no longer resting on the 4x4 wood blocks (D).

5.Turn the ignition switch OFF and remove the key. Remove the 4x4 blocks (D).

6.Use the mower belt release lever to release mower belt tension, and install the belt as shown in Figure 13.

D

Figure 12. Mower Hitch Components - 42 & 50” Decks

A.Hair Pin Clip

B.3/8-16 x 3/4 Carriage Bolt & Flange Nut

C.Hitch Rod

D.4x4 Wood Blocks

 

B

C

A

 

 

C

E

42” Deck

D

 

E

A

B

 

E

50” Deck

D

C

Figure 13. Mower Belt Routing - 42” & 50” Decks

A.Engine Pulley

B.Mower Drive Belt

C.Idler Pulleys

D.Mower Belt Release Lever

E.Arbor Pulleys

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 18.5, 21, 24, 26HP Zero-Turn Riders OPERATOR’S ManualPage Table of Contents General Operation Safety RulesIgnition System Suggested Guide for Sighting Slopes for Safe Operation Safe Handling of Gasoline Service & MaintenanceDecal Amputation Thrown Objects Hazard Decks Safety & Operation DecalsID Tag Identification NumbersControl Functions OperationGround Speed Levers Parking Brake LeverGeneral Operating Safety Fuel Recommendations Checks Before StartingStopping the Rider & Engine Emergency StoppingStarting the Engine Pushing the Rider by HandSmooth Travel Driving PracticeForward Travel Practice Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting Turns Executing an End-Of-Row Zero TurnRemoving the Mower Deck Installing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Maintenance Schedule MaintenanceRider MAINTENANCE, All Models 18.5, 21HP Briggs & StrattonClean Debris from Rider Engine Compartment Accessing the Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Check Tire PressureOil LubricationGrease Lubricating Mower Lift Blade Removal 33 Deck Clean Deck Check / Replace Mower BladesPage Operational Safety Checks Clean the Battery and CablesCheck Rider Safety System Adjust PTO Clutch Window Adjustment Nut Feeler Gauge Check / Adjust PTO ClutchChange Engine OIL & Filter Check Engine OIL LevelChange Engine OIL Air Filter Removal & Installation Service AIR Filter & PRE-CLEANER 18.5 & 21 HP EnginesAir Filter Cover Air Filter Cover Screws Service AIR Filter 24 & 26HP EnginesPre-Cleaner Service Clean Combustion Chamber Briggs & Stratton ModelsAir Filter Service Pre-Cleaner Replace Spark PlugGround Speed Control Lever Adjustment Service & AdjustmentsSpeed Balancing Adjustment Cutting Height AdjustmentBattery Charging Brake AdjustmentEngine Adjustments 62cmSide to Side Leveling 33 Decks Mower Deck Leveling AdjustmentsSide to Side Leveling 42 & 50 Decks Orient Blades Front-to-Back Front To Back Leveling 33 DeckDeck Front To Back Leveling 42 & 50 DecksMower Drive Belt Replacement 42 Decks Mower Belt ReplacementMower Drive Belt Replacement 33 Decks Storage StorageTroubleshooting the Rider TroubleshootingTroubleshooting the Mower Specifications Replacement Parts Service ItemsWATER, Fertilize HOW and When toAerate HOW High to MOW the GrassProper Mowing Speed When and HOW Often to MOW

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.
Top Page Image Contents