Snapper 150Z Series manual Storage

Page 37

Mower Drive Belt Replacement - 50” Decks

1.Park the rider on a level surface. Disengage the PTO, turn off the engine, set the ground speed control levers to START/PARK, and set the parking brake to ENGAGE. Remove the key.

2.Use the idler pulley arm (K, Figure 57) to release belt tension and remove the mower drive belt (F) from the PTO pulley (G).

3.Remove the belt from the remaining deck pulleys. Note: It is not necessary to remove the mower deck.

4.Install the new belt (F) as shown in Figure 57.

Arbor Drive Belt Replacement

Contact your local authorized dealer for replacement of the arbor drive belt (A, Figure 57).

G

A F

B

CE

D

HK I J

Figure 57. PTO Belt Routing

A.Arbor Drive Belt

B.Right Arbor Pulley

C.Arbor Idler Pulley

D.Center Arbor Pulley

E.Left Arbor Pulley

F.Mower Drive Belt

G.Engine PTO Pulley

H.Mower Drive Pulley

I.Mower Idler Pulley

J.Backside Idler Pulley

K.Idler Pulley Arm

STORAGE

STORAGE

Before Storage

Before you store your unit for the off-season, read the Maintenance and Storage instructions in the Safety Rules section, then perform the following steps:

•Turn the mower blades OFF, set the ground speed control levers to START / PARK, set the parking brake lever to ENGAGE, and remove the key from the ignition switch.

•Check all fluid levels. Check all maintenance items.

•Battery life will be increased if it is removed, put in a cool, dry place and fully charged about once a month. If the battery is left in the unit, disconnect the negative cable.

It is important to prevent gum deposits from forming in the essential fuel system parts such as the carburetor, fuel filter, fuel line, and fuel tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to the separation and formation of acids during storage. Acidic

WARNING

Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion.

Fuel vapor is also toxic to humans and animals.

gas can damage the fuel system of an engine while in storage.

To avoid engine problems use fuel stabilizer, especially before storage of 30 days or longer.

After Storage

Before starting the unit after it has been stored:

•Check all fluid levels. Check all maintenance items.

•Fill with FRESH fuel.

•After starting, allow the engine to warm before operating.

35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents 18.5, 21, 24, 26HP Zero-Turn Riders OPERATOR’S ManualPage Table of Contents General Operation Safety RulesIgnition System Suggested Guide for Sighting Slopes for Safe Operation Safe Handling of Gasoline Service & MaintenanceDecal Amputation Thrown Objects Hazard Decks Safety & Operation DecalsID Tag Identification NumbersControl Functions OperationGround Speed Levers Parking Brake LeverGeneral Operating Safety Fuel Recommendations Checks Before StartingStopping the Rider & Engine Emergency StoppingStarting the Engine Pushing the Rider by HandSmooth Travel Driving PracticeForward Travel Practice Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting Turns Executing an End-Of-Row Zero TurnRemoving the Mower Deck Installing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Maintenance Schedule MaintenanceRider MAINTENANCE, All Models 18.5, 21HP Briggs & StrattonClean Debris from Rider Engine Compartment Accessing the Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Check Tire PressureGrease LubricationOil Lubricating Mower Lift Blade Removal 33 Deck Clean Deck Check / Replace Mower BladesPage Check Rider Safety System Clean the Battery and CablesOperational Safety Checks Adjust PTO Clutch Window Adjustment Nut Feeler Gauge Check / Adjust PTO ClutchChange Engine OIL Check Engine OIL LevelChange Engine OIL & Filter Air Filter Removal & Installation Service AIR Filter & PRE-CLEANER 18.5 & 21 HP EnginesAir Filter Cover Air Filter Cover Screws Service AIR Filter 24 & 26HP EnginesPre-Cleaner Service Clean Combustion Chamber Briggs & Stratton ModelsAir Filter Service Pre-Cleaner Replace Spark PlugGround Speed Control Lever Adjustment Service & AdjustmentsSpeed Balancing Adjustment Cutting Height AdjustmentBattery Charging Brake AdjustmentEngine Adjustments 62cmSide to Side Leveling 33 Decks Mower Deck Leveling AdjustmentsSide to Side Leveling 42 & 50 Decks Orient Blades Front-to-Back Front To Back Leveling 33 DeckDeck Front To Back Leveling 42 & 50 DecksMower Drive Belt Replacement 33 Decks Mower Belt ReplacementMower Drive Belt Replacement 42 Decks Storage StorageTroubleshooting the Rider TroubleshootingTroubleshooting the Mower Specifications Replacement Parts Service ItemsWATER, Fertilize HOW and When toAerate HOW High to MOW the GrassProper Mowing Speed When and HOW Often to MOW

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.
Top Page Image Contents