Snapper 150Z Series manual Troubleshooting the Mower

Page 39

Engine runs, but

Transmission release levers in PUSH

Move levers to DRIVE positions.

rider will not

positions.

 

drive.

 

 

Drive belt slips.

Clean or replace belt as necessary.

 

 

 

 

Belt is broken.

Replace drive belt. Contact your local authorized dealer.

 

 

 

 

Parking brake is not fully released.

Contact your local authorized dealer.

 

 

 

Parking brake

Parking brake is incorrectly adjusted.

See Service & Adjustments Section.

will not hold.

 

 

 

 

 

Rider steers or

Improper tire inflation.

See Maintenance Section.

handles poorly.

 

 

Steering linkage is loose.

Check and tighten any loose connections.

 

 

 

 

Rider tracks to

Ground speed adjustment knobs not

See SPEED BALANCING ADJUSTMENT in Service &

one side.

adjusted.

Adjustments section.

 

 

 

Troubleshooting the Mower

PROBLEM

CAUSE

REMEDY

 

 

 

Mower cutting

Cutting height motor screw dirty or requires

Thoroughly clean and lubricate cutting height motor

height does not

lube.

screw.

adjust.

 

 

Cutting height linkage disconnected.

Check that mower linkage is connected.

 

 

 

 

Mower cut is

Rider tires not inflated equally or properly.

See Maintenance Section.

uneven.

 

 

Mower not leveled properly.

See "Mower Leveling" in Service & Adjustments.

 

 

 

 

Mower cut is

Engine speed too slow.

Always set engine speed to FAST when mowing.

rough looking.

 

 

Ground speed too fast.

Decrease ground speed.

 

 

 

 

 

Blades are dull.

Sharpen or replace blades. See Maintenance

 

 

Section.

 

 

 

 

Mower drive belt slipping because it is oily or

Clean or replace belt as necessary.

 

worn.

 

 

 

 

 

Blades not properly fastened to arbors.

See "Check/Replace Mower Blades" in Maintenance

 

 

Section.

 

 

 

Engine stalls

Engine speed too slow.

Always set engine speed to FAST when mowing.

easily with

 

 

Ground speed too fast.

Decrease Ground Speed.

mower engaged.

 

 

 

Cutting height set too low.

Cut tall grass at maximum cutting height during first

 

 

pass.

 

 

 

 

Underside of mower deck dirty.

Remove mower deck and clean underside.

 

 

 

 

Discharge chute jamming with cut grass.

Cut grass with discharge pointing toward previously

 

 

cut area.

 

 

 

Excessive

Blade mounting nuts are loose.

Torque as per instructions. See Maintenance

mower

 

Section.

vibration.

 

 

Mower blades, arbors, or pulleys are bent.

Check and replace as necessary.

 

 

 

 

Mower blades are out of balance.

Replace or balance blades. See Maintenance

 

 

Section.

 

 

 

 

Belt installed incorrectly.

Reinstall correctly.

 

 

 

Mower drive belt

Idler pulley spring broken or not properly

Repair or replace as needed.

slips or fails to

attached.

 

drive.

 

 

Mower drive belt broken.

Replace drive belt.

 

 

 

 

PTO clutch out of adjustment.

Adjust PTO clutch. See Maintenance Section.

 

 

 

37

Image 39
Contents 18.5, 21, 24, 26HP Zero-Turn Riders OPERATOR’S ManualPage Table of Contents General Operation Safety RulesIgnition System Suggested Guide for Sighting Slopes for Safe Operation Safe Handling of Gasoline Service & MaintenanceDecal Amputation Thrown Objects Hazard Decks Safety & Operation DecalsID Tag Identification NumbersParking Brake Lever OperationControl Functions Ground Speed LeversGeneral Operating Safety Fuel Recommendations Checks Before StartingPushing the Rider by Hand Emergency StoppingStopping the Rider & Engine Starting the EngineReverse Travel Practice Driving PracticeSmooth Travel Forward Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsRemoving the Mower Deck Installing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks 18.5, 21HP Briggs & Stratton MaintenanceMaintenance Schedule Rider MAINTENANCE, All ModelsCheck Tire Pressure Accessing the Engine CompartmentClean Debris from Rider Engine Compartment Clean Debris from Engine Cooling Areas and AIR FilterLubrication GreaseOil Lubricating Mower Lift Blade Removal 33 Deck Clean Deck Check / Replace Mower BladesPage Clean the Battery and Cables Check Rider Safety SystemOperational Safety Checks Adjust PTO Clutch Window Adjustment Nut Feeler Gauge Check / Adjust PTO ClutchCheck Engine OIL Level Change Engine OILChange Engine OIL & Filter Air Filter Removal & Installation Service AIR Filter & PRE-CLEANER 18.5 & 21 HP EnginesAir Filter Cover Air Filter Cover Screws Service AIR Filter 24 & 26HP EnginesReplace Spark Plug Clean Combustion Chamber Briggs & Stratton ModelsPre-Cleaner Service Air Filter Service Pre-CleanerCutting Height Adjustment Service & AdjustmentsGround Speed Control Lever Adjustment Speed Balancing Adjustment62cm Brake AdjustmentBattery Charging Engine AdjustmentsSide to Side Leveling 33 Decks Mower Deck Leveling AdjustmentsSide to Side Leveling 42 & 50 Decks Orient Blades Front-to-Back Front To Back Leveling 33 DeckDeck Front To Back Leveling 42 & 50 DecksMower Belt Replacement Mower Drive Belt Replacement 33 DecksMower Drive Belt Replacement 42 Decks Storage StorageTroubleshooting the Rider TroubleshootingTroubleshooting the Mower Specifications Replacement Parts Service ItemsHOW High to MOW the Grass HOW and When toWATER, Fertilize AerateProper Mowing Speed When and HOW Often to MOW

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.