Snapper 150Z Series manual Checks Before Starting, Fuel Recommendations

Page 12

CHECKS BEFORE STARTING

Check that the crankcase oil is filled to full mark on dipstick (see CHECK ENGINE OIL in the Maintenance section).

Fill the fuel tank with fresh fuel.

FUEL RECOMMENDATIONS

For daily operation: Use only unleaded gasoline with a pump sticker octane rating of 87 or higher. Gasohol (up to 10% ethyl alcohol, 90% unleaded gasoline by volume) is approved as a fuel. Methyl Teriary Butyl Ether (MTBE) and unleaded gasoline blends (up to a maximum of 15% MTBE by volume) are approved as a fuel. Do not use unapproved gasolines, such as E85. Do not mix oil in gasoline or modify the engine to run on alternate fuels. This will damage the engine components and void the engine warranty. Do not use fuel additives other than fuel stabilizer.

For storage: CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems always use fuel stabilizer, especially before storage of 30 days or longer. Use fresh fuel next season. See STORAGE instructions for additional information.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. To add fuel:

1.Remove the fuel cap (B, Figure 2).

2.Fill the tank. Do not overfill. Leave 2 inches (5 cm) of space in the tank for fuel expansion.

3.Install and hand tighten the fuel cap.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any reason, engage the parking brake and disengage the PTO. Never leave the unit unattended (i.e. out of sight) with the engine running.

To reduce fire hazard, keep the engine, rider and mower free of grass, leaves and excess grease. Do not stop or park rider over dry leaves, grass or combustible materials.

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

A

Figure 2. Pre-Start Checks

A. Fuel Tank Cap

WARNING

Never operate on slopes greater than 17.6 percent (10°) which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet (607 cm) horizontally.

Select slow ground speed before driving onto a slope. Use extra caution when operating on slopes with a rear-mounted grass catcher.

Mow up and down the face of slopes, not across. Use caution when changing directions and DO NOT START OR STOP ON A SLOPE.

WARNING - TRAILERS

Do not load this zero-turn rider on a trailer or truck using two separate ramps. Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider. This rider has a zero turning radius and the wheels could fall off the ramps, or the rider could tip over injuring the operator or bystanders.

10

Image 12
Contents OPERATOR’S Manual 18.5, 21, 24, 26HP Zero-Turn RidersPage Table of Contents Safety Rules General OperationIgnition System Suggested Guide for Sighting Slopes for Safe Operation Service & Maintenance Safe Handling of GasolineSafety & Operation Decals Decal Amputation Thrown Objects Hazard DecksIdentification Numbers ID TagOperation Control FunctionsGround Speed Levers Parking Brake LeverGeneral Operating Safety Checks Before Starting Fuel RecommendationsEmergency Stopping Stopping the Rider & EngineStarting the Engine Pushing the Rider by HandDriving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting Turns Executing an End-Of-Row Zero TurnInstalling the Mower Deck Removing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Maintenance Maintenance ScheduleRider MAINTENANCE, All Models 18.5, 21HP Briggs & StrattonAccessing the Engine Compartment Clean Debris from Rider Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Check Tire PressureLubrication GreaseOil Lubricating Mower Lift Clean Deck Check / Replace Mower Blades Blade Removal 33 DeckPage Clean the Battery and Cables Check Rider Safety SystemOperational Safety Checks Check / Adjust PTO Clutch Adjust PTO Clutch Window Adjustment Nut Feeler GaugeCheck Engine OIL Level Change Engine OILChange Engine OIL & Filter Service AIR Filter & PRE-CLEANER 18.5 & 21 HP Engines Air Filter Removal & InstallationService AIR Filter 24 & 26HP Engines Air Filter Cover Air Filter Cover ScrewsClean Combustion Chamber Briggs & Stratton Models Pre-Cleaner ServiceAir Filter Service Pre-Cleaner Replace Spark PlugService & Adjustments Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Cutting Height AdjustmentBrake Adjustment Battery ChargingEngine Adjustments 62cmMower Deck Leveling Adjustments Side to Side Leveling 33 DecksSide to Side Leveling 42 & 50 Decks Front To Back Leveling 33 Deck Orient Blades Front-to-BackFront To Back Leveling 42 & 50 Decks DeckMower Belt Replacement Mower Drive Belt Replacement 33 DecksMower Drive Belt Replacement 42 Decks Storage StorageTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Specifications Service Items Replacement PartsHOW and When to WATER, FertilizeAerate HOW High to MOW the GrassWhen and HOW Often to MOW Proper Mowing Speed

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.