Snapper 150Z Series manual Removing the Mower Deck, Installing the Mower Deck

Page 16

MOWER DECK REMOVAL & INSTALLATION - 33” DECKS

NOTE: Perform mower removal and installation on a hard, level surface such as a concrete floor.

WARNING

After lowering the mower cutting height, engage parking brake, turn off the mower blades, turn the ignition switch to STOP, and remove key before attempting to install or remove the mower.

A BC

A

Removing the Mower Deck

1.Turn the mower blades OFF, put the ground speed control levers in START/PARK position, engage the parking brake, turn the ignition OFF, and wait for all moving parts to stop.

2.Pivot the front wheels forward.

3.Pull the back-side idler pulley (C, Figure 11) forward to release belt tension. Remove the mower belt from engine PTO pulley (A).

4.Turn the ignition switch from OFF to RUN without starting the engine.

5.Use the mower cutting height switch to raise the mower deck.

6.Place 4x4 wood blocks (D, Figure 10) under the front and rear lip of the mower deck to securely support it.

7.Use the mower cutting height switch to fully lower the mower so that is it resting on the 4x4 wood blocks.

8.Turn the ignition switch to OFF and remove the key.

9.Remove the hair pin clips (A) securing the rear mower lift arms (B) and the front hitch rod (C) to the mower deck.

10.Separate the rear lift arms from the mower deck. Repeat on both sides of the mower.

11.Remove the front hitch rod (C) from the front hitch brackets.

12.Slide the mower deck out from under the rider.

Installing the Mower Deck

1.Slide the mower deck under the right side of the rider. Align the holes in the front hitch brackets, and insert the front hitch rod (C, Figure 10). Secure with hair pin clip (A).

2.Connect the rear lift arms to the mower deck. Secure with hair pin clips (A).

3.Insert the key into the ignition switch. Turn the switch from OFF to RUN without starting the engine.

4.Use the cutting height switch to raise the mower until it is no longer resting on the 4x4 wood blocks (D).

5.Turn the ignition switch OFF and remove the key. Remove the 4x4 blocks (D).

6.Release mower belt tension, and install the belt as shown in Figure 11.

D

Figure 10. Mower Hitch Components - 33” Decks

A.Hair Pin Clips

B.Rear Lift Arms

C.Front Hitch Rod

D.4x4 Wood Blocks

B

A

C

E

D

Figure 11. Mower Belt Routing - 33” Decks

A.Engine PTO Pulley

B.Mower Drive Belt

C.Back-Side Idler Pulley

D.Stationary Idler Pulley

E.Arbor Pulley

14

Page 15 Page 17
Image 16
Page 15 Page 17
Contents OPERATOR’S Manual 18.5, 21, 24, 26HP Zero-Turn RidersPage Table of Contents Safety Rules General OperationIgnition System Suggested Guide for Sighting Slopes for Safe Operation Service & Maintenance Safe Handling of GasolineSafety & Operation Decals Decal Amputation Thrown Objects Hazard DecksIdentification Numbers ID TagOperation Control FunctionsGround Speed Levers Parking Brake LeverGeneral Operating Safety Checks Before Starting Fuel RecommendationsEmergency Stopping Stopping the Rider & EngineStarting the Engine Pushing the Rider by HandDriving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting Turns Executing an End-Of-Row Zero TurnInstalling the Mower Deck Removing the Mower DeckMower Deck Removal & Installation 42 & 50 Decks Maintenance Maintenance ScheduleRider MAINTENANCE, All Models 18.5, 21HP Briggs & StrattonAccessing the Engine Compartment Clean Debris from Rider Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Check Tire PressureGrease LubricationOil Lubricating Mower Lift Clean Deck Check / Replace Mower Blades Blade Removal 33 DeckPage Check Rider Safety System Clean the Battery and CablesOperational Safety Checks Check / Adjust PTO Clutch Adjust PTO Clutch Window Adjustment Nut Feeler GaugeChange Engine OIL Check Engine OIL LevelChange Engine OIL & Filter Service AIR Filter & PRE-CLEANER 18.5 & 21 HP Engines Air Filter Removal & InstallationService AIR Filter 24 & 26HP Engines Air Filter Cover Air Filter Cover ScrewsClean Combustion Chamber Briggs & Stratton Models Pre-Cleaner ServiceAir Filter Service Pre-Cleaner Replace Spark PlugService & Adjustments Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Cutting Height AdjustmentBrake Adjustment Battery ChargingEngine Adjustments 62cmMower Deck Leveling Adjustments Side to Side Leveling 33 DecksSide to Side Leveling 42 & 50 Decks Front To Back Leveling 33 Deck Orient Blades Front-to-BackFront To Back Leveling 42 & 50 Decks DeckMower Drive Belt Replacement 33 Decks Mower Belt ReplacementMower Drive Belt Replacement 42 Decks Storage StorageTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Specifications Service Items Replacement PartsHOW and When to WATER, FertilizeAerate HOW High to MOW the GrassWhen and HOW Often to MOW Proper Mowing Speed

150Z Series specifications

The Snapper 150Z Series is a remarkable line of zero-turn mowers designed for both residential and commercial lawn care enthusiasts. Engineered for superior performance, this series combines durability, efficiency, and ease of use, making it a top choice for those who demand quality in their mowing equipment.

One of the standout features of the Snapper 150Z Series is its powerful engine options. The mowers are equipped with reliable Briggs & Stratton or Kohler engines, known for their robustness and fuel efficiency. This ensures that users can tackle even the most challenging mowing tasks with confidence, saving both time and fuel in the process.

A key characteristic of the Snapper 150Z Series is its unique zero-turn capability, which provides unmatched maneuverability. With a tight turning radius, these mowers can easily navigate around trees, flower beds, and other obstacles. This feature not only enhances the mowing experience but also helps achieve a precisely manicured lawn in less time compared to traditional lawn tractors.

The cutting deck is another notable element of the 150Z Series. Designed with a reinforced steel construction, it is built to withstand the rigors of lawn care while providing a clean and consistent cut. The mowers are available with various deck sizes, typically ranging from 42 to 50 inches, allowing users to choose a model that best fits their yard size and mowing needs. Additionally, the adjustable cutting height offers versatility, making it easy to customize the cut for different grass types and seasonal conditions.

Comfort and ergonomics are prioritized in the Snapper 150Z design. These mowers feature a plush, padded seat with armrests, allowing for extended periods of comfortable operation. The intuitive controls are designed for ease of use, making it accessible for both novice and experienced users alike.

Furthermore, the Snapper 150Z Series incorporates advanced technologies such as a dashboard display that provides essential information at a glance, from engine performance to maintenance reminders. This integration of technology enhances the overall user experience and promotes proactive maintenance.

In summary, the Snapper 150Z Series offers a perfect blend of power, precision, and comfort. With its robust engine options, zero-turn capabilities, durable cutting deck, and user-friendly design, it stands out as a reliable choice for anyone looking to elevate their lawn care game. Whether for residential or commercial use, the Snapper 150Z Series is engineered to deliver superior results with every mow.
Top Page Image Contents