Cub Cadet 7252 Steering Wheel, PTO Switch, Throttle Handle, Ignition Switch, Brake Pedal, Forward

Page 10

NOTE: References to LEFT and RIGHT indicate that side of the tractor when facing forward while seated in the drivers seat. Reference to FRONT indicates the grille end of the tractor; to REAR, the drawbar end.

A. Steering Wheel

The steering wheel is centered on the dash panel. It is used to change the direction (left or right) of the tractor while driving.

NOTE: This tractor is equipped with hydraulic power steering. With this feature, the cap and spokes of the steering wheel may change position.

B. PTO Switch

Slide Lock

Button

Figure 2

The PTO switch is a double action rocker type switch located to the right of the steering wheel on the dash panel. Slide the lock button rearward and push the top of the PTO switch downward to engage the PTO. Push the bottom of the switch downward to disengage.

C. Throttle Handle

This symbol indicates the fast position.

This symbol indicates the slow position.

The throttle handle is located to the right of the steering wheel on the dash panel. When set in a given position, a uniform engine speed will be maintained. Rotate the handle rearward to increase the engine speed.

D. Ignition Switch

NOTE: To prevent accidental starting and/or battery discharge, remove the key from the ignition switch when the tractor is not in use.

The ignition switch has three positions as follow:

OFF

STOP

ON

START

Figure 3

OFF - The engine and electrical system is turned off.

ON - The tractor electrical system is energized.

START- The starter motor will turn the engine. Release the key immediately when the engine starts

E. Brake Pedal

Brake Pedal

Symbol

Figure 4

The brake pedal is located at the front of the right floor board. Depress to engage the tractor brakes and neutralize the hydrostatic transmission. Fully depress the brake pedal to activate the safety interlock switch when starting the tractor.

F. Forward/Reverse Pedal

The forward/reverse pedal is a self neutralizing rocker style pedal located along the right floor board.

Forward Reverse

Pedal Pedal

Symbol Symbol

Figure 5

Forward

Slowly press down on the front of the pedal to start moving forward. The forward ground speed of the tractor is directly affected by the distance the front of the pedal is depressed.

Reverse

WARNING: Check behind the tractor to be sure the area is clear of people, pets or obstacles and use a slower speed to maintain control of the tractor when traveling in reverse.

Press down on the rear of the pedal to move in reverse.

G. Seat Adjustment Lever

The seat adjustment lever is located beneath the left side of the seat. This lever is used to adjust the seat forward or backward.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate Important Safe Operation Practices General OperationOperating the PTO Slope OperationChildren Do notSafety Frame Rops ServiceFAN Warning Label Located on Each Side of Radiator Safety LabelsStarting AID Keep HandsPTO Warning Label Located on Rear PTO Shield Battery Warning Label Located Under HoodRoll Over Warning Label Located on RIGHT/REAR Fender Controls and Features Floorboard and Dash Panel Mounted ControlsSeat Adjustment Lever PTO SwitchIgnition Switch Steering WheelDifferential Lock Pedal Hazard Light SwitchHeadlight Switch Parking Brake LeverParking Brake Indicator Light Battery Indicator LightEngine Coolant Temperature Light PTO Indicator LightFuel Fill Cap Fender Mounted Conrtols and FeaturesPTO Reverse Override Switch PTO Selection LeverHand Holds Transmission Hi/Lo Range Shift LeverCup Holder Amber Hazard LightsRollover Protective Structure Rops Safety Interlock SystemOperation Fueling the TractorStarting the Engine NEW Tractor BREAK-IN ProceduresThrottle Handle Slow Fast PTO Switch ‘OFF’ Position Cold Weather StartingDriving the Tractor Using Jumper Cables to Start the EngineStopping the Engine Driving on SlopesUsing the HI/LO Range Shift Lever Using the FORWARD/REVERSE PedalStopping the Tractor Using the Hydraulic Lift Lever Using the Differential Lock PedalHydraulic Lift Lever Using the PTO Selection Lever Engaging the PTOUsing the Three Point Hitch Using the PTO Reverse Override SwitchUsing the Hitch Plate LightingWeighting the Rear of the Tractor Tractor WeightingFront Weights Rear Weight BoxAdjusting the Seat Belt AdjustmentsAdjusting the Seat Three Point Hitch AdjustmentsJAM NUT Adjusting Front Wheel TOE-INAdjustment Tube HEX Shaft HEX JAM NUTAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesFeedback Links Rodhydraulic Lift Valve General Information Tractor MaintenanceLubrication Table API11 5 Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Storage Battery RemovalBattery Maintenance Battery Holddown ROD Wing NUT Holddown Strap Cable ClampHazard Bulb Replacement Head Light Bulb ReplacementTail Light Bulb Replacement Notch Lenses Bulb Socket Screw Inner Notch Housing OuterServicing Electrical System Instrument Panel Bulb ReplacementAccessing the Fuse Center Instrument Panel FusesHazard Light Flasher Relay Main FuseChecking TRANSMISSION/HYDRAULIC System OIL Level Hydrostatic Hydraulic System OIL Filter Changing TRANSMISSION/HYDRAULIC System OILTransmission Drain Plug Initial Break-In Period Filter Change Tire Inflation Chart Maintenance of the Rollover Protective Structure RopsTire Maintenance Lubrication of Drive ShaftTractor Storage Front of EngineRemoving the Tractor from Storage Engine Information and Maintenance Limited Liability Cleaning the Radiator Screen and Radiator Engine MaintenanceCleaning the Engine Before servicingHEX Drain Cock Engine Valve Adding Engine OILChanging the Engine OIL and Filter Full Mark OIL Filter Coolant ADD Mark ReservoirChecking Engine Coolant Level Remote Radiator CAP Filler Neck Overflow HoseChanging the Engine Coolant Changing the AIR CleanerInspection of Cooling System Hoses Overflow Reservoir Coolant Drain PlugServicing the Spark Plugs Servicing the Foam PrecleanerServicing the Paper Element Changing the Fuel FilterSpecifications Hydraulic Lift System Power Take-OffGeneral Dimensions BrakesDescription Optional Equipment and AccessoriesModel Number CUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7252 specifications

The Cub Cadet 7252 is a noteworthy addition to the lineup of robust and reliable lawn tractors designed for residential homeowners and landscaping professionals alike. This model combines power, versatility, and advanced technology to deliver an exceptional mowing experience.

One of the standout features of the Cub Cadet 7252 is its powerful engine. It is equipped with a reliable, air-cooled Kohler engine, providing ample horsepower to tackle even the most demanding mowing tasks. This engine delivers smooth and consistent performance, ensuring that users can cut through thick grass and uneven terrain with ease. The hydrostatic transmission further enhances functionality by offering a seamless driving experience without the need for manual gear shifting.

The cutting deck of the Cub Cadet 7252 is another highlight. With a wide 50-inch cutting deck, it allows for efficient mowing over large areas, reducing the time spent on lawn maintenance. The deck features a reinforced steel construction for durability and longevity, capable of withstanding the rigors of regular use. Additionally, users can achieve different cutting heights with ease, thanks to the 12 position height adjustment feature, ranging from 1 to 4 inches.

Technologically, the 7252 model integrates innovative features for enhanced comfort and ease of use. The ergonomic high-back seat provides maximum support during extended mowing sessions, while the comprehensive dashboard displays essential information, such as fuel level and engine status, allowing for better operation management.

Furthermore, this lawn tractor is designed with user convenience in mind. It features a tight turning radius, which makes maneuvering around obstacles such as trees and flower beds incredibly easy. The Cub Cadet 7252 also offers optional attachments like baggers and snow blowers, making it a versatile tool for various seasonal tasks beyond lawn care.

Overall, the Cub Cadet 7252 is engineered for performance, comfort, and versatility. Combining a powerful engine, wide cutting deck, and innovative technologies, it serves as an excellent solution for homeowners looking to maintain their lawns efficiently while enjoying the convenience of modern machinery.
Top Page Image Contents