Cub Cadet 7252 Adjusting Front Wheel TOE-IN, Adjustment Tube, Jam Nut, HEX Shaft HEX JAM NUT

Page 24

•The length of the upper hitch link is normally determined by the design of each implement. To adjust the upper hitch link, loosen the jam nut and turn the adjustment tube as shown in Figure 25. After the appropriate length is at- tained, tighten the jam nut. If correctly adjusted, the upper hitch link will be parallel or nearly parallel to the lower hitch links.

Lengthen

ADJUSTMENT TUBE

Shorten

JAM NUT

Figure 25

•The length of the hitch chains, attached to each lower hitch link, limit the side-to-side move- ment of the lower links. Loosen the jam nut and turn the chain’s hex shaft as shown in Figure 26 to adjust the length of the hitch chain. Tighten the jam nut after adjusting.

Turn Hex Shaft

 

to Lengthen

 

Loosen

 

Jam Nut

Turn Hex Shaft

 

to Shorten

HEX SHAFT

HEX JAM NUT

Figure 26

ADJUSTING FRONT WHEEL TOE-IN

The front wheel toe-in is set at the factory and should maintain the proper setting. However, the toe-in should be checked periodically and readjusted if necessary.

CHECK THE TOE-IN AS FOLLOWS:

•Place the tractor on a level surface with the wheels in the straight ahead position.

•Place an easily visible mark on the center lines of both front tires at the horizontal center line of the wheel.

•Measure and record the distance ‘A’ between the two marks. See Figure 27.

•Roll the tractor forward or rearward until the marks are at the horizontal center line at the rear of the wheels. Measure and record the distance ‘B’ between the marks. See Figure 27.

•Distance ‘A’ should be 1/8"-1/4" less than distance ‘B’ if the toe-in is correct. If it is not, readjust the toe-in.

A

B

Figure 27

READJUST THE TOE-IN AS FOLLOWS:

NOTE: The left ball joint and jam nut are left hand threaded.

•Loosen the jam nuts at both the LH and RH ball joints. See Figure 28.

•Slide an open-end wrench onto the flat area at either end of the tie rod and turn the tie rod as follows:

Rearward to shorten the tie rod and increase the toe-in. See Figure 28.

Forward to lengthen the tie rod and decrease the toe-in. See Figure 28.

Front of

Tractor

Increase

Toe-in

Decrease

Toe-in

TIE ROD

JAM NUT

RH BALL JOINT

Figure 28

•Readjust the tie rod as necessary to obtain the correct toe-in, then tighten the jam nuts against the ball joints.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Tractor Model PlateRops Information Plate Important Safe Operation Practices General OperationSlope Operation ChildrenOperating the PTO Do notSafety Frame Rops ServiceSafety Labels Starting AIDFAN Warning Label Located on Each Side of Radiator Keep HandsBattery Warning Label Located Under Hood PTO Warning Label Located on Rear PTO ShieldRoll Over Warning Label Located on RIGHT/REAR Fender Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverBattery Indicator Light Engine Coolant Temperature LightParking Brake Indicator Light PTO Indicator LightFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsSafety Interlock System OperationRollover Protective Structure Rops Fueling the TractorNEW Tractor BREAK-IN Procedures Throttle Handle Slow Fast PTO Switch ‘OFF’ PositionStarting the Engine Cold Weather StartingUsing Jumper Cables to Start the Engine Stopping the EngineDriving the Tractor Driving on SlopesUsing the FORWARD/REVERSE Pedal Using the HI/LO Range Shift LeverStopping the Tractor Using the Differential Lock Pedal Using the Hydraulic Lift LeverHydraulic Lift Lever Using the PTO Selection Lever Engaging the PTOUsing the PTO Reverse Override Switch Using the Hitch PlateUsing the Three Point Hitch LightingTractor Weighting Front WeightsWeighting the Rear of the Tractor Rear Weight BoxAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Adjustment TubeJAM NUT HEX Shaft HEX JAM NUTAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODFeedback Links Rodhydraulic Lift Valve Tractor Maintenance Lubrication TableGeneral Information API11 5 Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Removal Battery MaintenanceBattery Storage Battery Holddown ROD Wing NUT Holddown Strap Cable ClampHead Light Bulb Replacement Tail Light Bulb ReplacementHazard Bulb Replacement Notch Lenses Bulb Socket Screw Inner Notch Housing OuterInstrument Panel Bulb Replacement Accessing the Fuse CenterServicing Electrical System Instrument Panel FusesMain Fuse Hazard Light Flasher RelayChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Hydrostatic Hydraulic System OIL FilterTransmission Drain Plug Initial Break-In Period Filter Change Maintenance of the Rollover Protective Structure Rops Tire MaintenanceTire Inflation Chart Lubrication of Drive ShaftFront of Engine Tractor StorageRemoving the Tractor from Storage Engine Information and Maintenance Limited Liability Engine Maintenance Cleaning the EngineCleaning the Radiator Screen and Radiator Before servicingAdding Engine OIL Changing the Engine OIL and FilterHEX Drain Cock Engine Valve Full Mark OIL Filter Coolant ADD Mark ReservoirChecking Engine Coolant Level Remote Radiator CAP Filler Neck Overflow HoseChanging the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Overflow Reservoir Coolant Drain PlugServicing the Foam Precleaner Servicing the Paper ElementServicing the Spark Plugs Changing the Fuel FilterSpecifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories DescriptionModel Number CUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7252 specifications

The Cub Cadet 7252 is a noteworthy addition to the lineup of robust and reliable lawn tractors designed for residential homeowners and landscaping professionals alike. This model combines power, versatility, and advanced technology to deliver an exceptional mowing experience.

One of the standout features of the Cub Cadet 7252 is its powerful engine. It is equipped with a reliable, air-cooled Kohler engine, providing ample horsepower to tackle even the most demanding mowing tasks. This engine delivers smooth and consistent performance, ensuring that users can cut through thick grass and uneven terrain with ease. The hydrostatic transmission further enhances functionality by offering a seamless driving experience without the need for manual gear shifting.

The cutting deck of the Cub Cadet 7252 is another highlight. With a wide 50-inch cutting deck, it allows for efficient mowing over large areas, reducing the time spent on lawn maintenance. The deck features a reinforced steel construction for durability and longevity, capable of withstanding the rigors of regular use. Additionally, users can achieve different cutting heights with ease, thanks to the 12 position height adjustment feature, ranging from 1 to 4 inches.

Technologically, the 7252 model integrates innovative features for enhanced comfort and ease of use. The ergonomic high-back seat provides maximum support during extended mowing sessions, while the comprehensive dashboard displays essential information, such as fuel level and engine status, allowing for better operation management.

Furthermore, this lawn tractor is designed with user convenience in mind. It features a tight turning radius, which makes maneuvering around obstacles such as trees and flower beds incredibly easy. The Cub Cadet 7252 also offers optional attachments like baggers and snow blowers, making it a versatile tool for various seasonal tasks beyond lawn care.

Overall, the Cub Cadet 7252 is engineered for performance, comfort, and versatility. Combining a powerful engine, wide cutting deck, and innovative technologies, it serves as an excellent solution for homeowners looking to maintain their lawns efficiently while enjoying the convenience of modern machinery.
Top Page Image Contents