Cub Cadet 7252 manual Adjusting the Seat Belt, Three Point Hitch Adjustments

Page 23

SECTION 3: ADJUSTMENTS

ADJUSTING THE SEAT

For the comfort of the operator, a single lever adjustable seat is provided to set the fore to aft position of the seat. Adjust the seat to the most comfortable position that allows you to operate all controls and pedals.

WARNING: Do not adjust the seat when the tractor is moving, as this could cause the operator to lose momentary control of the tractor and result in an accident.

•To adjust the seat, pivot the seat adjustment lever to the left and hold while repositioning the seat to the desired position.

•After repositioning the seat, release the lever to lock the seat in position. Slide the seat either slightly forward or rearward to assure it is locked or until engagement of the lock is felt. See Figure 22.

 

Pivot Lever

SEAT

to Left

ADJUSTMENT

LEVER

Figure 22

ADJUSTING THE SEAT BELT

WARNING: Always wear the seat belt when operating the tractor equipped with a ROPS. However, if the ROPS has been removed, the seat belt should not be used.

NOTE: If the belt is too long or too short to be prop- erly adjusted using the upper belt webbing, the adjustment clip should be repositioned. To do so, firmly grasp the adjustment clip and pull the lower webbing though the clip. Move the clip toward the anchor point at the seat to shorten the belt, or toward the buckle link the lengthen the belt.

Adjust the final length of the seat belt using the adjuster clip, buckle link, and upper belt webbing on the right half of the belt.

•To lengthen the belt, hold the ends of the adjuster clip and tip upward the side of the clip toward the buckle link. See Figure 23.

•While holding the clip, pull the upper webbing of the belt through the clip toward the buckle link. See Figure 23.

•Hold the belt and pull the buckle link to the left to remove the slack in the upper webbing of the belt between the adjuster clip and the link.

RELEASE

BUCKLE Tip Sides of Clip

Pull Belt to

Pull Belt to

BUTTON

 

Lengthen

Shorten

BUCKLE

 

ADJUSTER

 

CLIP

LINK

UPPER

LOWER

 

 

WEBBING

WEBBING

Figure 23

•To shorten the belt, tip the other side of the clip upward, pull the free end of the belt webbing to the right, and pull the buckle link to the left to remove the slack.

THREE POINT HITCH ADJUSTMENTS

•Adjust the RH adjustable lift link to level the lower hitch links. Loosen the jam nut and turn the adjustment tube as shown in Figure 24 to shorten or lengthen the lift link. Tighten the jam nut against the adjustment tube after adjusting.

Loosen

JAM

Jam Nut

NUT

ADJUSTMENT

ShortenTUBE

Lengthen

Figure 24

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTo the Owner Table of ContentsCalling Service Information Rops Information Plate Recording Model and Serial Number InformationTractor Model Plate General Operation Important Safe Operation PracticesDo not Slope OperationChildren Operating the PTOService Safety Frame RopsKeep Hands Safety LabelsStarting AID FAN Warning Label Located on Each Side of RadiatorRoll Over Warning Label Located on RIGHT/REAR Fender Battery Warning Label Located Under HoodPTO Warning Label Located on Rear PTO Shield Floorboard and Dash Panel Mounted Controls Controls and FeaturesSteering Wheel PTO SwitchIgnition Switch Seat Adjustment LeverParking Brake Lever Hazard Light SwitchHeadlight Switch Differential Lock PedalPTO Indicator Light Battery Indicator LightEngine Coolant Temperature Light Parking Brake Indicator LightPTO Selection Lever Fender Mounted Conrtols and FeaturesPTO Reverse Override Switch Fuel Fill CapAmber Hazard Lights Transmission Hi/Lo Range Shift LeverCup Holder Hand HoldsFueling the Tractor Safety Interlock SystemOperation Rollover Protective Structure RopsCold Weather Starting NEW Tractor BREAK-IN ProceduresThrottle Handle Slow Fast PTO Switch ‘OFF’ Position Starting the EngineDriving on Slopes Using Jumper Cables to Start the EngineStopping the Engine Driving the TractorStopping the Tractor Using the FORWARD/REVERSE PedalUsing the HI/LO Range Shift Lever Hydraulic Lift Lever Using the Differential Lock PedalUsing the Hydraulic Lift Lever Engaging the PTO Using the PTO Selection LeverLighting Using the PTO Reverse Override SwitchUsing the Hitch Plate Using the Three Point HitchRear Weight Box Tractor WeightingFront Weights Weighting the Rear of the TractorThree Point Hitch Adjustments AdjustmentsAdjusting the Seat Adjusting the Seat BeltHEX Shaft HEX JAM NUT Adjusting Front Wheel TOE-INAdjustment Tube JAM NUTFeedback Links Rodhydraulic Lift Valve Adjusting the BrakesAdjusting Hydraulic Lift Feedback ROD API Tractor MaintenanceLubrication Table General Information11 5 Service Intervals Operation to Lubrication and Maintenance ChartGeneral Battery Information Accessing the Engine CompartmentBattery Holddown ROD Wing NUT Holddown Strap Cable Clamp Battery RemovalBattery Maintenance Battery StorageNotch Lenses Bulb Socket Screw Inner Notch Housing Outer Head Light Bulb ReplacementTail Light Bulb Replacement Hazard Bulb ReplacementInstrument Panel Fuses Instrument Panel Bulb ReplacementAccessing the Fuse Center Servicing Electrical SystemChecking TRANSMISSION/HYDRAULIC System OIL Level Main FuseHazard Light Flasher Relay Transmission Drain Plug Changing TRANSMISSION/HYDRAULIC System OILHydrostatic Hydraulic System OIL Filter Initial Break-In Period Filter Change Lubrication of Drive Shaft Maintenance of the Rollover Protective Structure RopsTire Maintenance Tire Inflation ChartRemoving the Tractor from Storage Front of EngineTractor Storage Engine Information and Maintenance Limited Liability Before servicing Engine MaintenanceCleaning the Engine Cleaning the Radiator Screen and RadiatorFull Mark OIL Filter Coolant ADD Mark Reservoir Adding Engine OILChanging the Engine OIL and Filter HEX Drain Cock Engine ValveRemote Radiator CAP Filler Neck Overflow Hose Checking Engine Coolant LevelOverflow Reservoir Coolant Drain Plug Changing the AIR CleanerInspection of Cooling System Hoses Changing the Engine CoolantChanging the Fuel Filter Servicing the Foam PrecleanerServicing the Paper Element Servicing the Spark PlugsSpecifications Brakes Power Take-OffGeneral Dimensions Hydraulic Lift SystemModel Number Optional Equipment and AccessoriesDescription CLEVELAND, Ohio CUB Cadet LLC Post Office BOX

7252 specifications

The Cub Cadet 7252 is a noteworthy addition to the lineup of robust and reliable lawn tractors designed for residential homeowners and landscaping professionals alike. This model combines power, versatility, and advanced technology to deliver an exceptional mowing experience.

One of the standout features of the Cub Cadet 7252 is its powerful engine. It is equipped with a reliable, air-cooled Kohler engine, providing ample horsepower to tackle even the most demanding mowing tasks. This engine delivers smooth and consistent performance, ensuring that users can cut through thick grass and uneven terrain with ease. The hydrostatic transmission further enhances functionality by offering a seamless driving experience without the need for manual gear shifting.

The cutting deck of the Cub Cadet 7252 is another highlight. With a wide 50-inch cutting deck, it allows for efficient mowing over large areas, reducing the time spent on lawn maintenance. The deck features a reinforced steel construction for durability and longevity, capable of withstanding the rigors of regular use. Additionally, users can achieve different cutting heights with ease, thanks to the 12 position height adjustment feature, ranging from 1 to 4 inches.

Technologically, the 7252 model integrates innovative features for enhanced comfort and ease of use. The ergonomic high-back seat provides maximum support during extended mowing sessions, while the comprehensive dashboard displays essential information, such as fuel level and engine status, allowing for better operation management.

Furthermore, this lawn tractor is designed with user convenience in mind. It features a tight turning radius, which makes maneuvering around obstacles such as trees and flower beds incredibly easy. The Cub Cadet 7252 also offers optional attachments like baggers and snow blowers, making it a versatile tool for various seasonal tasks beyond lawn care.

Overall, the Cub Cadet 7252 is engineered for performance, comfort, and versatility. Combining a powerful engine, wide cutting deck, and innovative technologies, it serves as an excellent solution for homeowners looking to maintain their lawns efficiently while enjoying the convenience of modern machinery.
Top Page Image Contents