Cub Cadet 7252 manual NEW Tractor BREAK-IN Procedures, Starting the Engine, Cold Weather Starting

Page 16

The fuel fill cap is located on the fender to the left of the seat. Unscrew the fuel cap and fill tank from an approved gasoline container. Immediately wipe up any spilled fuel.

WARNING: Never fill the fuel tank to the top of the filler neck. Expansion could result in overflow through the vents in the cap, allowing highly flammable fuel to come in contact with the operator.

NEW TRACTOR BREAK-IN PROCEDURES

Proper care during the first hours of operation will help to assure optimal performance from your new tractor.

•Never operate a new engine immediately under full load. Allow the engine to warm up.

•Avoid operating the engine for prolonged periods at either high or low speeds with no load.

•Use the transmission’s low speed range for heavy loads to avoid lugging of the engine due to overload.

•Closely monitor the engine oil and coolant levels, and keep filled to the recommended levels.

•After the first ten hours of operation, check all of the front and rear wheel bolts. If necessary, retighten to the following torque:

Front Wheels — 55 ft. lbs. Rear Wheels — 80 ft. lbs.

•Perform all break-in maintenance procedures found in the MAINTENANCE section.

STARTING THE ENGINE

WARNING: Always sit in the operator’s seat when starting the tractor, Never attempt to start the engine while standing beside the tractor.

•Operator must be sitting in the tractor seat.

•Pull the choke control knob out to the full choke position. Less choking may be necessary due to variations in temperature, grade of fuel, etc. Little or no choking will be needed when the engine is warm.

•Move the throttle handle to midway between the “SLOW” and “FAST” position. Refer to Figure 14.

•Make sure the PTO switch is in the “OFF” position. Note: The PTO light on instrument panel will flash if switch is in ON position.

THROTTLE

HANDLE

SLOW

FAST

PTO SWITCH

IN ‘OFF’

POSITION

Figure 14

•Either fully depress and hold the brake pedal or engage the parking brake. Note: The parking brake indicator on instrument panel will flash if pedal is not depressed.

•Turn the ignition key clockwise to the “START” position and release it as soon as the engine starts; however, do not crank the engine continuously for more than 10 seconds at a time. If the engine does not start within this time, turn the key to “OFF” and wait a minute to allow the engine’s starter motor to cool. Try again after waiting. If after a few attempts the engine fails to start, do not keep trying to start it with the choke closed as this will cause flooding and make starting more difficult. Instead, fully open the choke and start the engine.

•After the engine starts, slowly release the brake pedal. As the engine warms up, gradually push the choke control knob all the way in. Do not use the choke to enrich the fuel mixture, except as necessary to start the engine.

•After the engine has started, let the engine run for approximately three to five minutes at mid throttle before putting the engine under load.

•Observe the instrument panel. If the battery indicator light, oil pressure light, or coolant temperature light comes on, immediately stop the engine. Have the tractor inspected by your Cub Cadet dealer.

COLD WEATHER STARTING

Follow the normal engine starting instructions above.

•An optional engine coolant heater is available from your Cub Cadet dealer. This heater will aid in starting the tractor when ambient temperatures fall below 10°F (-12°C).

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate Important Safe Operation Practices General OperationSlope Operation ChildrenOperating the PTO Do notSafety Frame Rops ServiceSafety Labels Starting AIDFAN Warning Label Located on Each Side of Radiator Keep HandsPTO Warning Label Located on Rear PTO Shield Battery Warning Label Located Under HoodRoll Over Warning Label Located on RIGHT/REAR Fender Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverBattery Indicator Light Engine Coolant Temperature LightParking Brake Indicator Light PTO Indicator LightFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsSafety Interlock System OperationRollover Protective Structure Rops Fueling the TractorNEW Tractor BREAK-IN Procedures Throttle Handle Slow Fast PTO Switch ‘OFF’ PositionStarting the Engine Cold Weather StartingUsing Jumper Cables to Start the Engine Stopping the EngineDriving the Tractor Driving on SlopesUsing the HI/LO Range Shift Lever Using the FORWARD/REVERSE PedalStopping the Tractor Using the Hydraulic Lift Lever Using the Differential Lock PedalHydraulic Lift Lever Using the PTO Selection Lever Engaging the PTOUsing the PTO Reverse Override Switch Using the Hitch PlateUsing the Three Point Hitch LightingTractor Weighting Front WeightsWeighting the Rear of the Tractor Rear Weight BoxAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Adjustment TubeJAM NUT HEX Shaft HEX JAM NUTAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesFeedback Links Rodhydraulic Lift Valve Tractor Maintenance Lubrication TableGeneral Information API11 5 Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Removal Battery MaintenanceBattery Storage Battery Holddown ROD Wing NUT Holddown Strap Cable ClampHead Light Bulb Replacement Tail Light Bulb ReplacementHazard Bulb Replacement Notch Lenses Bulb Socket Screw Inner Notch Housing OuterInstrument Panel Bulb Replacement Accessing the Fuse CenterServicing Electrical System Instrument Panel FusesHazard Light Flasher Relay Main FuseChecking TRANSMISSION/HYDRAULIC System OIL Level Hydrostatic Hydraulic System OIL Filter Changing TRANSMISSION/HYDRAULIC System OILTransmission Drain Plug Initial Break-In Period Filter Change Maintenance of the Rollover Protective Structure Rops Tire MaintenanceTire Inflation Chart Lubrication of Drive ShaftTractor Storage Front of EngineRemoving the Tractor from Storage Engine Information and Maintenance Limited Liability Engine Maintenance Cleaning the EngineCleaning the Radiator Screen and Radiator Before servicingAdding Engine OIL Changing the Engine OIL and FilterHEX Drain Cock Engine Valve Full Mark OIL Filter Coolant ADD Mark ReservoirChecking Engine Coolant Level Remote Radiator CAP Filler Neck Overflow HoseChanging the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Overflow Reservoir Coolant Drain PlugServicing the Foam Precleaner Servicing the Paper ElementServicing the Spark Plugs Changing the Fuel FilterSpecifications Power Take-Off General DimensionsHydraulic Lift System BrakesDescription Optional Equipment and AccessoriesModel Number CUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7252 specifications

The Cub Cadet 7252 is a noteworthy addition to the lineup of robust and reliable lawn tractors designed for residential homeowners and landscaping professionals alike. This model combines power, versatility, and advanced technology to deliver an exceptional mowing experience.

One of the standout features of the Cub Cadet 7252 is its powerful engine. It is equipped with a reliable, air-cooled Kohler engine, providing ample horsepower to tackle even the most demanding mowing tasks. This engine delivers smooth and consistent performance, ensuring that users can cut through thick grass and uneven terrain with ease. The hydrostatic transmission further enhances functionality by offering a seamless driving experience without the need for manual gear shifting.

The cutting deck of the Cub Cadet 7252 is another highlight. With a wide 50-inch cutting deck, it allows for efficient mowing over large areas, reducing the time spent on lawn maintenance. The deck features a reinforced steel construction for durability and longevity, capable of withstanding the rigors of regular use. Additionally, users can achieve different cutting heights with ease, thanks to the 12 position height adjustment feature, ranging from 1 to 4 inches.

Technologically, the 7252 model integrates innovative features for enhanced comfort and ease of use. The ergonomic high-back seat provides maximum support during extended mowing sessions, while the comprehensive dashboard displays essential information, such as fuel level and engine status, allowing for better operation management.

Furthermore, this lawn tractor is designed with user convenience in mind. It features a tight turning radius, which makes maneuvering around obstacles such as trees and flower beds incredibly easy. The Cub Cadet 7252 also offers optional attachments like baggers and snow blowers, making it a versatile tool for various seasonal tasks beyond lawn care.

Overall, the Cub Cadet 7252 is engineered for performance, comfort, and versatility. Combining a powerful engine, wide cutting deck, and innovative technologies, it serves as an excellent solution for homeowners looking to maintain their lawns efficiently while enjoying the convenience of modern machinery.
Top Page Image Contents