Husky 70 Series, 1800 Series manual Installation Instructions, Installing Hose and Nozzle

Page 10

GASBOY Series 70 & 1820

INSTALLATION INSTRUCTIONS

Cabinet Removal for Installation or Service (Series 1820 Only) - Rounded Cabinet

1.Remove two screws, one on each side of the cabinet.

2.Pull front panel assembly forward at bottom. As it clears the pumping unit, lift up to remove.

3.To replace front panel, engage pins at top in matching holes in rear panel. With front panel assembly tilted back, pins may be seen through dial opening. Front panel assembly will now drop back into position.

4.Reinstall two screws in sides.

Cabinet Removal for Installation or Service (Series 1820R Only) - Squared Cabinet

1.Remove two screws on lower front of cabinet.

2.Remove two screws from upper back of cabinet.

3.Push in and hold the reset button and pivot the cabinet front panel upward until it clears the button (Be careful not to damage the button). Remove panel.

4.For calibration or service, remove the lefthand side panel by unscrewing the two screws on the bottom side of the cabinet.

5.To reassemble pump cabinet, align side panel screw holes with holes on base of cabinet and screw tight. Replace the cabinet top and front panel by positioning the back plate and pivoting the assembly forward. Be sure to press in the reset button until the front panel clears it. Then replace the screws in the front and back of cabinet.

Installing Hose and Nozzle

To prevent undue stress and possible damage, install hose and nozzle after installation of pump. Hose must have static wire which provides electrical continuity between hose couplings to dissipate static electrical charge.

1.Screw the pipe elbow (provided with the pump) into the product outlet on the back of the pump. Apply gasoline-resistant pipe compound to male threads.

NOTE:

Elbow fitting is not required, however, it provides strain relief for the hose.

2.Screw the hose into the open end of the elbow and tighten. Apply gasoline-resistant pipe compound to male threads.

3.Screw nozzle onto hose.

NOTE: 1820R models are shipped with a vacuum breaker assembly (P/N 032701) consisting of a tee, pipe nipple and vacuum breaker. This assembly should be installed in the pump outlet before connecting the hose.

2-4

9312

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installers Important Gasboy INTERNATIONAL, INC. a Tokheim Subsidiary LANSDALE, PAImportant Warnings and Safeguards Gasboy INTERNATIONAL, INCContents Warranty Gasboy Series 70Introduction SpecificationsPurpose Series 70 and 1820 Features Installation Installation PrecautionsSupply Line Underground Tanks Pump Dimensions Series 70, Model Pump Dimensions Model 1820RInstallation Instructions Installing Hose and NozzleDirect Mount on Underground Tanks Direct Mount on Aboveground Tank Pedestal Mount Pump Wall Mount Vacuum Breaker As requiredTesting the Vacuum Breaker Wiring Precautions WiringCircuit Breakers Grounding Wire SizeWire Size Pump MotorPulser Wiring ConduitPump Wiring Diagrams Startup and Operation PRE-STARTUP ChecklistStartup Voltage Strainer CleaningPOST-STARTUP Tests TightnessDaily Operation Start-Up and OperationPage Maintenance and Troubleshooting Maintaining TROUBLE-FREE OperationWhen Your Pump Needs Service Pump hums but wont start TroubleshootingPump Wont Start Pump runs but wont prime or deliver productPump delivery is slow Pump delivers product when not turned onPump delivers product but wont register Pump loses primeDisassembly of Pump METER-REGISTER DisassemblyReplacing Bearing and Seal Assembly Item 36, Old Style 1860 3-WHEEL Register Service and MaintenanceReplacing Bearing and Seal Assembly Item 36, New Style 4860 4-WHEEL Register Service Replacing Bearing and Seal Assembly Item 16, Old StyleReplacing Bearing and Seal Assembly Item 26, New Style Parts Series 70 Assembly Optional Accessories Series 1820 Assembly See Direct Drive Motor parts breakdown Direct Drive MOTOR-PUMP Assembly Description Installation Parts 4860 METER-REGISTER Register Assemblies1860 3-WHEEL Meter Register for Model Change GEARS-IMPERIAL Gallons 4860 4-WHEEL Register for Model 72S and Series 1820R Change GEARS-US Gallons New Style Gasoline or Diesel Gasboy Series 70 Optional Kits for Series 70 and 1800 Pumps Gasboy Series 70 Model 1820R Parts List 1820R Pulser and Junction BOX Assemblies Warranty
Top Page Image Contents