Zenoah EXZ2610DL owner manual Controlling Blade Bounce, Transporting the Unit

Page 22

EXZ2610DL

8. Operation (Optional blade usage BC-EX only)

WARNING

Make sure to use shoulder strap and cutting attach- ment guard. If not, it is very dangerous when you slip or lose your balance.

WARNING

CONTROLLING BLADE BOUNCE

Blade thrust can cause serious personal injury. Care- fully study this section. It is important that you un- derstand what causes blade thrust, how you can re- duce the chance of blade thrust and how you can remain in control of the unit if blade thrust does oc- cur.

1.What causes blade thrust:

blade thrust can occur when the moving blade contacts an object that it cannot cut. This contact causes the blade to stop for an instant and then suddenly move or “bounce” away from the object that was hit. The operator can lose control of the unit and the blade can cause serious personal injury to the operator or any person nearby if the blade contacts any part of the body.

2.How you can reduce the chance of blade thrust:

a. Recognize that blade thrust can happen. By un- derstanding and knowing about bounce, you can help eliminate the element of surprise.

b. Cut fibrous weeds and grass only. Do not let the blade contact materials it cannot cut such as hard, woody vines and bushes or rocks, fences, metal, etc.

c. Be extra prepared for bounce if you must cut where you cannot see the blade making contact such as in areas of dense growth.

d. Keep the blade sharp. A dull blade increases the chance of bounce.

e. Avoid feeding the blade too rapidly. The blade can bounce away from material being cut if the blade is fed faster than its cutting capability.

f. Cut only from your right to your left.

g.Keep your path of advance clear of material that has been cut and other debris.

3.How you can maintain the best control:

a.Keep a good, firm grip on the unit with both hands. A firm grip can help neutralize bounce. Keep your right and left hands completely around the respec- tive handles.

b.Keep both feet spread apart in a comfortable stance and yet braced for the possibility that the unit could bounce. Do not overreach. Keep firm footing and balance.

MAINTENANCE

BLADE

Check the blade and the fasteners for looseness, cracking, or bending.

Check the cutting edges and reform with a flat file. Point:

Saw blade

1.9 ~ 2.2 mm

R1 ~ 1.5 mm.08 in R .04 in

8-teeth blade

R2 ~ 3 mm

R .09 in

R3 ~ 4 mm

R .13 in

1 ~ 2 mm

.01 in

4-teeth blade

R2 ~ 3 mm

R .09 in

R4 ~ 5 mm

R .18 in

3 ~ 4 mm

R .13 in

1.Keep the end corner sharp.

2.Round the root of the edge, using a round file.

3.Do not use water when using a grinder.

IMPORTANT

It is recommended that filing should be done by pro- fessionals.

Especially regarding filing the saw blade, leave it to the professionals.

TRANSPORTING THE UNIT

When you finish cutting in one location and wish to continue work in another spot, turn off the engine, lift up the unit and carry it, paying attention to the blade.

Never forget to place the protective cover over the blades.

When transporting the unit over long distances, de- tach the blade and fasten the unit by ropes.

GB-22

Image 22
Contents EXZ2610DL Wear head, eye and ear protection E13*97/68SH2G3*2002/88*0404*00Contents Parts location EXZ2610DL-PUO BC-EX LRT-EX PS-EX HE-EXSpecification BC-EXSymbols on the machine Never modify your machineWorking Circumstance For safe operationWorking Condition Working PlanBefore Starting Engine Using the ProductStarting the Engine Handling Fuel MaintenanceIf Someone Comes TransportationGB-10 Connecting Throttle Wire Set upMounting Engine Installing Handle Connecting Switch WiresSet up BC-EX only Attaching the Trimming Mechanism Set up LRT-EX onlySet up PS-EX only Balance UnitSet up HE-EX only Put on strap and attach unit to strapFuel and chain oil Adjusting Wheel Height Adjusting Handle PositionOperation Stopping Engine Adjusting Throttle Cable Adjusting Idling SpeedCutting Work Line Head Usage Adjusting the Line LengthOperation BC-EX only Trimming Grass and WeedsNy lon line SET UPOperation Optional blade usage BC-EX only Choose the BladeCutting Method OperationZenoah Controlling Blade Bounce Transporting the UnitOperation PS-EX only Adjusting the angle of the cutting bladesOperation LRT-EX only Checking oil supplyOperation HE-EX only AIR Filter MaintenanceFuel Filter Muffler Replacement Plug is a NGK CMR7HSpark Plug Spark ArresterFor safety reasons, do not use metalreinforced line Maintenance BC-EX onlyProcedures to be Performed After Every 100 Hours of USE Refilling Trimming LineBlades Maintenance LRT-EX onlyAngle Transmission TransmissionGuide BAR Maintenance PS-EX onlyOiling Port Sprocket025 0.65 mm Disposal Maintenance HE-EX only StorageTroubleshooting guide Check Probable Causes ActionLimited warranty