Zenoah EXZ2610DL owner manual If Someone Comes, Maintenance, Handling Fuel, Transportation

Page 9

5. For safe operation

(PS-EX only)

7. Never operate the pruner at an

 

 

angle greater than 60° in order to

 

 

reduce the risk of being struck by

 

 

falling objects during operation.

 

 

 

 

 

 

WARNING

 

Approaching or contacting elec- tric power lines with pruning saw may cause serious injury or death from electrocution.

Electricity can jump from one point to another by means of arc- ing or may be conducted through damp branches. Maintain a clear- ance of at least 15m between Pole saw and any electrical line carry- ing live current.

IF SOMEONE COMES

1.Guard against hazardous situa- tions at all times. Warn adults to keep pets and children away from the area. Be careful if you are ap- proached. Injury may result from flying debris.

2.If someone calls out or otherwise interrupts you while working, al- ways be sure to turn off the en- gine before turning around.

MAINTENANCE

1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals.

2.Always be sure to turn off the en- gine and disconnect the spark plug wire before performing any maintenance or checking proce- dures.

WARNING

The metallic parts reach high tem- peratures immediately after stop- ping the engine.

3. When replacing the cutting at- tachment or any other part, or when replacing the oil or any lu- bricant, always be sure to use only ZENOAH products or products which have been cer- tified by ZENOAH for use with the ZENOAH product.

4.In the event that any part must be replaced or any maintenance or repair work not described in this

EXZ2610DL

manual must be performed, please contact a representative from the store nearest ZENOAH authorized servicing dealer for assistance.

5.Do not use any accessory or at- tachment other than those bear- ing the ZENOAH mark and rec- ommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product be- coming damaged during opera- tion or the product becoming un- able to operate properly.

HANDLING FUEL

1. The engine of the ZENOAH prod- uct is designed to run on a mixed fuel, which contains highly flam- mable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always

turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames any- where nearby before refueling.

4.Wipe spilled fuel completely us- ing a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 3 m or more away from where it was refueled before turning on the en- gine.

TRANSPORTATION

1. When hand-carrying the product, cover over the cutting part if nec- essary, lift up the product and carry it paying attention to the blade.

2. Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank dur- ing transport.

GB-9

G B

Image 9
Contents EXZ2610DL E13*97/68SH2G3*2002/88*0404*00 Wear head, eye and ear protectionContents EXZ2610DL-PUO BC-EX LRT-EX PS-EX HE-EX Parts locationBC-EX SpecificationNever modify your machine Symbols on the machineWorking Condition For safe operationWorking Circumstance Working PlanUsing the Product Before Starting EngineStarting the Engine If Someone Comes MaintenanceHandling Fuel TransportationGB-10 Mounting Engine Installing Handle Set upConnecting Throttle Wire Connecting Switch WiresSet up BC-EX only Set up PS-EX only Set up LRT-EX onlyAttaching the Trimming Mechanism Balance UnitPut on strap and attach unit to strap Set up HE-EX onlyFuel and chain oil Adjusting Handle Position Adjusting Wheel HeightOperation Stopping Engine Adjusting Idling Speed Adjusting Throttle CableOperation BC-EX only Adjusting the Line LengthCutting Work Line Head Usage Trimming Grass and WeedsOperation Optional blade usage BC-EX only SET UPNy lon line Choose the BladeOperation Cutting MethodZenoah Transporting the Unit Controlling Blade BounceOperation LRT-EX only Adjusting the angle of the cutting bladesOperation PS-EX only Checking oil supplyOperation HE-EX only Maintenance AIR FilterFuel Filter Spark Plug Replacement Plug is a NGK CMR7HMuffler Spark ArresterProcedures to be Performed After Every 100 Hours of USE Maintenance BC-EX onlyFor safety reasons, do not use metalreinforced line Refilling Trimming LineAngle Transmission Maintenance LRT-EX onlyBlades TransmissionOiling Port Maintenance PS-EX onlyGuide BAR Sprocket025 0.65 mm Troubleshooting guide Maintenance HE-EX only StorageDisposal Check Probable Causes ActionLimited warranty