Zenoah EXZ2610DL owner manual Operation HE-EX only

Page 24

EXZ2610DL

8.Operation (PS-EX only)

Adjust the pump as follows:

1.Stop the engine and make sure the stop switch is in the OFF position.

2.Place the unit on its side with the oil reservoir up.

(1) Oil tank (2) Chain cover

IMPORTANT

The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw.

3.With a screwdriver, push in on the oil flow rate adjust- ing screw and turn in the desired direction (there are three incremental settings):

(a)Clockwise-decrease lubrication

(b)Counter clockwise-increase lubrication

(c)Middle

WARNING

Always wear work gloves made of leather or some other sturdy material when using the polesaw.

Falling branches may fall onto the face or into the eyes, resulting in injuries, scratches, and cuts, and for this reason you should always be sure to wear a helmet and face protector when using your polesaw.

8.Operation (HE-EX only)

WARNING

Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury.

Keep the blade guard and the mad guard attached in place at all times when the unit is operated.

Before starting a job, check the area and remove all obstacles and objects that could be thrown by the blade.

Do not adjust the wheel height or try to remove anything entangled to the blade with the engine running.

1.Before starting the engine, adjust the wheel height for desired cutting depth (see page 15).

2.Before starting a job, plan your direction of travel so that you can always hold the edger on you right side and can walk on a hard surface as much as possible.

3.When starting to edge, run the engine at full throttle, and slowly have the blade cut into the edge groove.

BLADE

ROTATION

NOTE

Do not use the HE-EX to make a new groove into the ground. Such usage will not be covered by ZENOAH Warranty.

GB-24

Image 24
Contents EXZ2610DL Wear head, eye and ear protection E13*97/68SH2G3*2002/88*0404*00Contents Parts location EXZ2610DL-PUO BC-EX LRT-EX PS-EX HE-EXSpecification BC-EXSymbols on the machine Never modify your machineFor safe operation Working ConditionWorking Circumstance Working PlanUsing the Product Before Starting EngineStarting the Engine Maintenance If Someone ComesHandling Fuel TransportationGB-10 Set up Mounting Engine Installing HandleConnecting Throttle Wire Connecting Switch WiresSet up BC-EX only Set up LRT-EX only Set up PS-EX onlyAttaching the Trimming Mechanism Balance UnitSet up HE-EX only Put on strap and attach unit to strapFuel and chain oil Adjusting Handle Position Adjusting Wheel HeightOperation Stopping Engine Adjusting Throttle Cable Adjusting Idling SpeedAdjusting the Line Length Operation BC-EX onlyCutting Work Line Head Usage Trimming Grass and WeedsSET UP Operation Optional blade usage BC-EX onlyNy lon line Choose the BladeOperation Cutting MethodZenoah Controlling Blade Bounce Transporting the UnitAdjusting the angle of the cutting blades Operation LRT-EX onlyOperation PS-EX only Checking oil supplyOperation HE-EX only Maintenance AIR FilterFuel Filter Replacement Plug is a NGK CMR7H Spark PlugMuffler Spark ArresterMaintenance BC-EX only Procedures to be Performed After Every 100 Hours of USEFor safety reasons, do not use metalreinforced line Refilling Trimming LineMaintenance LRT-EX only Angle TransmissionBlades TransmissionMaintenance PS-EX only Oiling PortGuide BAR Sprocket025 0.65 mm Maintenance HE-EX only Storage Troubleshooting guideDisposal Check Probable Causes ActionLimited warranty