Troy-Bilt 675B manual Problem, Correction

Page 23

moving partsto come to a complete stop, disconnectspark plug wire and move wire awayfrom WARNING: Beforeinspecting, cleaning or servicing the machine,shut off engine, wait for all

spark plug. Failureto follow these instructions can result in serious personal injury or property damage.

TROUBLESHOOTING

PROBLEM

 

POSSIBLECAUSE

Enginedoes not start

1.

Spark plug wire disconnected

 

2.

Engine Throttle Control Lever incorrectly set.

 

3.

Fuel tank empty.

 

4.

Choke control (if so equipped) in incorrect position.

 

5.

Stale gasoline.

 

6.

Dirty air filter.

 

7.

Defective or incorrectly gapped spark plug.

 

8.

Carburetor out of adjustment.

 

9.

Misadjusted throttle control.

 

10.

Dirt or water in fuel tank.

Enginerunspoorly.

1.

Defective or incorrectly gapped spark plug.

 

2.

Dirty air filter(s).

 

3.

Carburetor out of adjustment.

 

4.

Stale gasoline.

 

5.

Dirt or water in fuel tank.

 

6.

Engine cooling system clogged.

Engineoverheats.

1.

Engine cooling system clogged.

 

2.

Carburetor out of adjustment.

 

3.

Oil level is low.

CORRECTION

Reconnectwire.

2.Put lever in STARTposition.

3.Add fuel.

4.See Engine Owner'sManual.

5.Drain fuel and add fresh fuel.

6.Clean or replace filter.

7.Inspect spark plug.

8.See Engine Service Dealer.

9.See Engine Service Dealer

10.See Engine Service Dealer.

Inspect spark plug (see Engine Owner'sManual).

2.Clean or replace (see Engine Owner'sManual).

3.See Engine Service Dealer.

4.Replacewith fresh gasoline.

5.See Engine Service Dealer.

6.Cleanair cooling system (see Engine Owner'sManual). Cleanair cooling area (see Engine Owner'sManual).

2.See Engine Service Dealer.

3.Check oil level (see Engine Owner'sManual).

Enginedoesnotshutoff WheelsandTineswill notturn

Tinesturn,butwheelsdon't,

1.Misadjusted throttle control or ignition switch.

1.Improper useof controls.

2.Forward Drive: Misadjusted forward clutch rod.

3.Reverse Drive. Broken or misadjusted belt.

4.Worn Broken or misadjusted Drive Belt(s).

5.Internal transmission wear or damage.

6.Bolt and key loose in transmission pulley.

1.Wheel Drive Pins not in WHEEL DRIVE.

2.Bolt loose in transmission pulley.

3.Internal transmission wear or damage.

1.See Engine Owner'sManual or Engine Service Dealer.

1.Review Sections 3 and 4.

2.See "Handlebar Height Adjustment," Section 3.

3.Replacebelt or adjust belt tension. Section 5.

4.See "Checking Drive Belt Tension," Section 5.

5.Contact local dealer or the factory.

6.Tighten bolt. Check that key is in place.

1.See "Wheel Drive Pins" in Section 3.

2.Tighten bolt.

3.Contact local Dealer or the Factory.

WheelsTurn,butTinesDon't,

Poortillingperformance.

1.Tine holder mounting hardware missing.

2.Internal transmission wear or damage.

1.Worn tines.

2.Improper Depth Regulator setting.

3.Incorrect throttle setting or belt range speed.

4.Belt(s) slipping.

1.Replacehardware.

2.Contact local Dealer or the Factory.

1.See "Tines" (Section 5).

2.See "Tilling Tips & Techniques," Section 4.

3.See Section 4.

4.See "Checking Forward Drive Belt Tension," Section 5.

23

Image 23
Contents 13/04 Formno -00586BFindingmodelnumber Operation SafetySafetyAlert Symbol TrainingGearLevertoENGAGE MaintenanceandStorageOrinspections Itawayfromthesparkplug.MoveWheelFast SafetyDecalsOperatingSymbols HotSurfacesMovingBeltsRef. Qty. Description AssemblyTools/ MaterialsNeeded For Assembly HardwareBag PartsListAttachforwardclutch Controlcable Attachreverseclutch ControlcableCheckair Whentension is correct, tighten the two jam nuts B securelyChecktransmissiongear OIL Level AttachwheelgearleverForwardClutchLevers FeaturesandcontrolsTiller Features Recoil Starter To AdjustHandlebarHeightEngineControls DepthRegulatorLeverStarting and Stopping Engine OperationWheelsand tines, releaseboth le OperatingTillerStoppingtheEngine Contact your telephoneTo Changefrom Highto LowSpeed ChangingBelt RangeSpeedsStoppingtheTiller andEngine ToChangefrom Lowto HighSpeedWith planning, you can ==..vp Tilling DepthsLet the Tiller Dothe Work AvoidMaking Footprints AvoidTilling Soggy,Wet SoilTilling Up and DownSlopesVertical Tilling Wahning Do not Clearingthe TinesLoading and UnloadingtheTiller Read the followingrecommendationsbeforetilling on slopesCheck Tire Air Pressure MaintenanceEndCap Transmission Gear Oil Service CheckHardwareEngineCleaning Air CleanerServiceSpark Plug Service Off SeasonStorage Meansthe cuttingedges face CheckingAndAdjustingTensionToCheckandAdjustTensiononthe Forward DriveBelt On DriveBeltsTo Checkand AdjustTensionon the Re- verse Drive Belt Removingthe ForwardDriveBelt Forward Drive Belt Removal InstallationInstallingthe ForwardDriveBelt Removingthe ReverseDriveBelt Installingthe ReverseDriveBeltReverse Drive Belt Removal Correction ProblemPartslist Handlebar Assembly and Control LeversDescription MODEL675B25, Ref Reve rseScrew, Ref , secures ForwardClutchCableLockwasher-546 BeltGuide,WireFormedHexHd.Screw,546-18 x 2-1/4 Bracket,ClutchCablePartno Description See NotePartno GW-9572 GW-9944 GW-1714 La GW-9400 Lb GW-9401 GW-20718 GW-9301 1916597WheelShaftIncl.Ref.6 OilSealShim,1-1J64I.D.,.O62thickA/R Shim,asabove,but.OlOthickA/ROFDENOTEST,NECUTT,NGEDGEI Transmission 618-04002 Bracket,Hood&DepthRegulator RollPinspiral,1/4x1BarAssembly,DepthAdjustment Hood,TineBumper 0EM-290-254 ROW Marker Attachment OptionalREF no TROY-BILTLLC, P.O. Box 361131, Cleveland, Ohio 44136-0019 TROY-BILT Tiller Lifetime Limited Warranty