Craftsman 917.29921 Tools Required for Assembly, Operators Position, Install Depth Stake Assembly

Page 6

Your new tiller has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)Utility knife

(2)1/2 Wrench

OPERATOR'S POSITION

When right or left hand is mentioned in this manual, it means when you are in the oper- ating position (standing behind tiller handles).

Front

LeftRight

Operator's Position

UNPACK CARTON & INSTALL HANDLE

_CAUTION: Be careful of exposed sta- ples when handling or disposing of carton- ing material.

IMPORTANT: When unpacking and as- sembling tiller, be careful not to stretch or kink cable(s).

1.Cut cable ties securing handle column.

2.Route cable(s) as shown and slide handle column onto handle mount.

3.Remove all packing from carton.

4.Secure handle column using two (2) carriage bolts and two (2) flange lock- nuts. Tighten securely.

5.Cut away carton.

6.Route tine control cable(s) through

plastic cable clip on handle mount. NOTE: Cables must not touch the muffler.

7.Cut cable ties securing tiller to skid.

Remove tiller from skid by pulling back- wards.

8.Remove screws securing depth stake to skid and discard the screws.

Tine

Control

Cable

Column

Handle "_

)unt I

Flange

Locknut

INSTALL DEPTH STAKE

ASSEMBLY

1.Loosen nut'S'.

2.Insert stake support between engine bracket halves with stake spring down.

3.Bolt stake support to engine brackets with bolts, lock washers and nuts.

Tighten securely. Tighten nut '7_'.

4.Depth stake must move freely. If it does not, loosen support bolt.

Engine Bracket Halves

Nut '_'

Depth Stake Support

Depth

Stake pport Bolt

Spring

Hex Bolts, Lock

Washers, and hex Nuts

HANDLE HEIGHT

•Handle height may be adjusted to better suit operator. (See "HANDLE HEIGHT"

in the Service and Adjustments section of this manual),

TILLING WIDTH

• Tilling width may be adjusted to better handle your tilling conditions (See "TINE ARRANGEMENT" in the Service and

Adjustments section of this manual).

TINE OPERATION

•Check tine operation before first use. (See "TINE OPERATION CHECK" in the Service and Adjustments section of this manual).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Rrftsmrm Preparation Sears Service Back CoverLimited ONE Year Warranty on Craftsman Tiller TrainingMaintenance and Storage OperationCustomer Responsibilities Product SpecificationsSears Installation Service Repair ProtectionContents of Hardware Pack Install Depth Stake Assembly Tools Required for AssemblyUnpack Carton & Install Handle Operators PositionKnow Your Tiller TillerDepth Stake ADD Gasoline Before Starting EngineFill Engine with OIL To Start EngineBreaking in Your Tiller Tilling HintsPage General Recommendations Lubrication ChartKeep unit well lubricated See LUBRI- Cation Chart Before Each USESw-3o,mI AIR CleanerEngine Lubrication LevelTransmission CleaningSpark Plug MufflerRemove outer tines To Adjust Handle HeightTiller Tine Operation CheckBelt Replacement To Replace V-BELTTo Remove Belt Guard Fuel System OtherTiller CylinderLoss of power Troubleshooting ChartProblem Cause CorrectionTroubleshooting Chart Problem Cause CorrectionHandling Soil balls up or clumps Entrenamiento PreparacionMantenimiento Y Almacenamiento Responsabilidades DEL Cliente UNC MotorMantenimiento DE LA Cultivadora Instalacion DEL Conjunto DE LA Herraiviientas Necesarias Para EL MontajeDesempaque DE LA Caja DE Carton E Instalacin DEL Mango Estaca DE ProfundidadConozca SU Cultivadora Control DE LOS Brazos Marcha HALOS Dientes Como Utilizar LA CultivadoraLabrado EL MotorLlene EL Motor CON Aceite Para Arrancar EL MotorAntes DE Arrancar EL Motor Agregue GasounaConsejos Para Labrar Cultivo Antes DE Cada USO Programa DE MantenimientoRecomendaciones Generales LubricacionRelleno DEL Motor CON Aceite 5w..-,30Motor Lubricacion Para Cambiar EL Aceite DEL MotorTransmision Sistema DE EnfriamientoSilenciador LimpiezaOBOl Remocion DE LA Correa REVISIONFINALENLAPOSICIONDEEN- CendidoonPara Cambiar LA Correa Cambio DE LA CorreaAceite DEL Motor CU LtivadoraSistema DE Combustible OtrosProblema Identificacion DE ProblemasProblema Causa Identificacion DE ProblemasCorreccion KEY HandlesKEY Part NO. no PartBelt Guard and Pulley Assembly Wheel and Depth Stake Assembly KEY PartTine Assembly Tiller - Model NumberTiller = = Model Number TRANSMiSSiONDecals KEY PartDESCRiPTiON ENGINE, LCT-- Model Number PLMHK14600124P-AB ENGINE, LCT ==MODEL Number PLMHK14600124P=AB Page Page Your Home Our Home
Top Page Image Contents