Craftsman 917.29921 Tiller, To Adjust Handle Height, Remove outer tines, Tine Operation Check

Page 15

_CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT

Factory assembly has provided lowest handle height. Select handle height best

suited for your tilling conditions. Handle

height will be different when tiller digs into soil.

1.If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets.

2.Slide handle panel to desired location.

3.Tighten the four nuts securely.

Engine Brackets

Panel

Nuts(Also 2 on Left Side of Tiller

•Assemble holes '_'in tine hubs to holes "C" in tine shaft.

AC

• Remove outer tines.

NOTE: When reassembling outer tines,

OO oo]tine6

Inner Tines Only

be sure right tine assembly (marked "R")

and left tine assembly (marked "L') are mounted to correct side of tine shaft.

TINE ARRANGEMENT

Your outer tines can be assembled in

several different ways to suit your tilling or cultivating needs.

&CAUTION: Tines are sharp. Wear gloves or other protection when handling tines.

•Assemble holes '_'in tine hubs to holes "B" in tine shaft.

-- Clevis Pin

Outer Tine

J ,;?

°f, -

Hawpm Clip

\ Inner Tine

TINE OPERATION CHECK

_f_WARNING: Disconnect spark plug wire from spark plug to prevent starting while checking tine operation.

For proper tine operation, tine control lever

must be against control body and all slack removed from inner wire of control cable

when control is in the "OFF" (up) position. If lever and cable are loose, loosen cable clip at lower end of cable. Pull up on cable to remove slack, without extend- ing spring on end of cable, and retighten cable clip.

1.With tine control "OFF" (up), push down on handle to raise tines off the

ground.

2.Slowly pull recoil starter handle while observing tines. Tines should not rotate.

3.If tines rotate, inner wire of control cable is too tight which is extend- ing lower spring and engaging tines. Loosen cable clip and push down on cable only enough to relieve spring tension. Tighten cable clip.

4.Recheck in "OFF" position and adjust if necessary.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Rrftsmrm Training Sears Service Back CoverLimited ONE Year Warranty on Craftsman Tiller PreparationOperation Maintenance and StorageRepair Protection Product SpecificationsSears Installation Service Customer ResponsibilitiesContents of Hardware Pack Operators Position Tools Required for AssemblyUnpack Carton & Install Handle Install Depth Stake AssemblyTiller Know Your TillerDepth Stake To Start Engine Before Starting EngineFill Engine with OIL ADD GasolineTilling Hints Breaking in Your TillerPage Before Each USE Lubrication ChartKeep unit well lubricated See LUBRI- Cation Chart General RecommendationsLevel AIR CleanerEngine Lubrication Sw-3o,mIMuffler CleaningSpark Plug TransmissionTine Operation Check To Adjust Handle HeightTiller Remove outer tinesBelt Replacement To Replace V-BELTTo Remove Belt Guard Cylinder OtherTiller Fuel SystemCause Correction Troubleshooting ChartProblem Loss of powerTroubleshooting Chart Problem Cause CorrectionHandling Soil balls up or clumps Preparacion EntrenamientoMantenimiento Y Almacenamiento Responsabilidades DEL Cliente UNC MotorMantenimiento DE LA Cultivadora Estaca DE Profundidad Herraiviientas Necesarias Para EL MontajeDesempaque DE LA Caja DE Carton E Instalacin DEL Mango Instalacion DEL Conjunto DE LAControl DE LOS Brazos Marcha HA Conozca SU CultivadoraEL Motor Como Utilizar LA CultivadoraLabrado LOS DientesAgregue Gasouna Para Arrancar EL MotorAntes DE Arrancar EL Motor Llene EL Motor CON AceiteConsejos Para Labrar Cultivo Lubricacion Programa DE MantenimientoRecomendaciones Generales Antes DE Cada USOPara Cambiar EL Aceite DEL Motor 5w..-,30Motor Lubricacion Relleno DEL Motor CON AceiteLimpieza Sistema DE EnfriamientoSilenciador TransmisionOBOl Cambio DE LA Correa REVISIONFINALENLAPOSICIONDEEN- CendidoonPara Cambiar LA Correa Remocion DE LA CorreaOtros CU LtivadoraSistema DE Combustible Aceite DEL MotorIdentificacion DE Problemas ProblemaProblema Causa Identificacion DE ProblemasCorreccion Part HandlesKEY Part NO. no KEYBelt Guard and Pulley Assembly KEY Part Wheel and Depth Stake AssemblyTiller - Model Number Tine AssemblyTRANSMiSSiON Tiller = = Model NumberDecals KEY PartDESCRiPTiON ENGINE, LCT-- Model Number PLMHK14600124P-AB ENGINE, LCT ==MODEL Number PLMHK14600124P=AB Page Page Our Home Your Home
Top Page Image Contents