Craftsman 247.88855 owner manual Attaching Turn Triggers, Lamp Wiring, Trigger Cable

Page 10

Attaching Turn Triggers

Make sure that the right hand trigger cable is routed in front of the traction drive cable.

Feed the trigger cable up through the outer side of the slot in the handle panel. Do not feed the cable through the same side of the slot as the Z fitting.

Place the cable barrel fitting into the hole in the trigger. You can find the triggers and associated hardware in group H of the hardware pack (on page 5). Pull on the cable and rotate it around the bottom of the trigger, with the inner cable in the slot, until the cable end can be pushed into the trigger housing and snapped tight. See Figure 12.

Trigger

Assembly

Inner Cable

Trigger

Housing

Cable

Barrel

 

 

Slot Cable snaps in at

Fitting

 

 

this end

Figure 12

Note: When the cable is installed correctly, it should not be possible to pull cable out of the trigger housing.

Place the right turn trigger in position underneath the right handle. Secure with screw and weld nut from group H of the hardware pack. See Figure 13. You will need a phillips screwdriver for tightening the screw. Repeat on left side.

Secure with screw

Weld Nut

Turn

Trigger

Slot

Trigger

 

Cable

Figure 13

Secure the right turn trigger cable to the right lower handle, using cable tie provided in the

hardware pack. Make sure to route the cable tie over the drive cable. See Figure 14.

Trigger Cable

Cable Tie

Figure 14

Secure the left turn trigger cable to the lower handle using the other cable tie. Make sure to route the cable tie below the auger drive cable so that when the trigger cable is secured by the cable tie, the auger drive cable is left outside the cable tie.Trim excess ends from each cable tie.

NOTE: The right side cable tie must be used to keep cable from coming in contact with the moving shift arm from the transmission.

Lamp Wiring

Wrap the wire from the lamp down the right handle. Plug wire into the alternator lead wire under the fuel tank. See Figure 15.

Trigger Cable

Handle

Lamp

Wire

Alternator

Lead

Figure 15

IMPORTANT: Assemble your snow thrower, then check the adjustments as instructed and make any final adjustments necessary before operating the unit. Failure to follow the instructions may cause damage to the snow thrower.

10

Image 10
Contents 247.888550 Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.ATable of Contents Warranty InformationSafe Operation Practices TrainingMaintenance and Storage Hardware Pack Spare PartRemoving From Carton AssemblyAttaching Handle Assembly Loose PartsAttaching Chute Attaching Chute CrankNut Attaching Clutch Cables Attaching Shift RodAttaching Turn Triggers Lamp WiringTrigger Cable Adjusting Traction Drive Control Final AdjustmentsAdjusting Auger Control Adjusting Skid ShoeOperation Meets Ansi Safety StandardsKnowing Your Snow Thrower Operating Controls To Stop The Snow ThrowerFill Gas Before Starting EngineTo Start Engine Electric StarterOperating Snow Thrower Before Stopping To Throw SnowOperating Tips To Engage AugersGeneral Recommendations MaintenanceCustomer Responsibilities Check V-belts LubricationCheck Friction Wheel Engine Maintenance Service & Adjustments AdjustmentsService Drive Belt Friction Wheel RubberCarburetor Preparing Engine OFF-SEASON StoragePreparing Snow Thrower TROUBLE-SHOOTING Problem Possible Cause Corrective ActionParts List Polo Green Powder Black 80 17 Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Labels Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Key Description Qty Carburetor 900 Piston, & Pin Ass’y..010 OS Table from previous Recoil Starter Optional Garantia DE Información Especificaciones DEL ProductoPracticas Seguras DE Operacion EntrenamientoMantenimiento Y Almacenamiento Conjunto DE Ferreteria Piezas de RepuestoEnsamblado Fijacion Del Conjunto Del MangoFijacion De La Canaleta Fijacion De La Manivela De La CanaletaSoporte de la Fijacion De Los Cables Del Embrague Fijacion De La Vara De CambiosFijacion De Los Gatillos De Giro Ajuste del Control de la Hélice Cableado de la LámparaAjustes Finales Ajuste del Control del Propulsor de TracciónAjuste de la Zapata Deslizante Operacion Conozca Su Expulsor De NieveDetencion Del Expulsor De Nieve Para Expeler NieveLlene Con Gasolina Antes De Arrancar El MotorPara Arrancar El Motor Vea la Figura Arrancador ElectricoArrancador De Retroceso Para Apagar El MotorArranque En Caliente Arrancador De Retroceso CongeladoConsejos De Operacion Para Enganchar El PropulsorInstrucciones Abreviadas de Arranque Lubricacion MantenimientoRecomendaciones Generales Responsabilidades del clienteMantenimiento del Motor Control Del Propulsor De Traccion Vara De CambiosAjustes HelicesExtraccion Y Reemplazo De La Correa CarburadorCorreas De La Helice Placa Raspadoras Y Zapatas Deslizantes Goma De La Rueda De FriccionPreparación del motor Almacenamiento DE Fuera DE TemporadaPreparación del Expulsor de Nieve Problema Causas posible Accion Correctora Tabla DE Localizacion DE FallasYour Notes Comments contd Date HomeCentralSM