Craftsman 247.88855 owner manual Service & Adjustments

Page 20

SERVICE & ADJUSTMENTS

WARNING: Always stop the engine, dis- connect spark plug wire and move it away from the spark plug before performing any adjustments or repairs.

Never attempt to clean the chute or make any adjustments while the engine is running.

Adjustments

Traction Drive Control

Refer to the Final Adjustment section of the Set-Up Instructions to adjust the traction drive control. If you are not sure of proper adjustment, check as follows.

•Drain the gasoline or place plastic film under the gas cap if the snow thrower has already been operated.

•Tip the snow thrower forward and remove the four self-tapping screws that hold the frame cover underneath the snow thrower.

•With the traction drive control released, make sure that there is clearance between the friction wheel and the friction plate in all positions of the shift lever. See Figure 22.

Drive Shaft

Drive

Cable

Sprocket

Shaft

Pivot

NOTE: If you placed plastic under the gas cap, be certain to remove it.

Augers

The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a foreign object or ice jam, the snow thrower is designed so that the bolts will shear.

•If the augers will not turn, check to see if the bolts have sheared. Replace if necessary. See Figure 23. Two replacement shear bolts and hex lock nuts have been provided in Group D of the hardware pack which is illustrated on page 5.

Shear Bolt

Figure 23

Auger Clutch

To adjust the auger clutch, refer to Final Adjustment section of Assembly Instructions.

Chute Assembly

The distance snow is thrown can be adjusted by

Friction Wheel

Rod

adjusting the angle of the chute assembly.

Skid Shoe

Friction

Plate

Figure 22

•With the traction drive control engaged, make sure that the friction wheel is making contact with the friction plate. Also make sure that the overtravel spring is stretched.

•If adjustment is necessary, loosen the jam nut on the traction drive cable and thread the cable in or out as necessary.

•Tighten the jam nut to secure the cable when correct adjustment is reached. Reassemble the frame cover.

The space between the shave plate and the ground can be adjusted by adjusting the skid shoe. Refer to page 11 of this manual.

Shift Rod

To adjust the shift rod, proceed as follows.

•Remove the hairpin clip and flat washer from the ferrule underneath the shift panel. Remove the ferrule from the hole in the shift lever.

•Place the shift lever on the handle panel in the sixth (6) speed position (all the way forward).

•Push down on the shift rod (and shift arm assembly) as far as it will go. Hold it in this position. See Figure 24.

•Thread the ferrule up or down the shift rod as necessary until the ferrule lines up with the upper hole in the shift lever.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 247.888550 Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.ATable of Contents Warranty InformationSafe Operation Practices TrainingMaintenance and Storage Hardware Pack Spare PartAssembly Attaching Handle AssemblyRemoving From Carton Loose PartsAttaching Chute Attaching Chute CrankNut Attaching Clutch Cables Attaching Shift RodTrigger Cable Lamp WiringAttaching Turn Triggers Final Adjustments Adjusting Auger ControlAdjusting Traction Drive Control Adjusting Skid ShoeKnowing Your Snow Thrower Meets Ansi Safety StandardsOperation Operating Controls To Stop The Snow ThrowerBefore Starting Engine To Start EngineFill Gas Electric StarterOperating Snow Thrower To Throw Snow Operating TipsBefore Stopping To Engage AugersCustomer Responsibilities MaintenanceGeneral Recommendations Check Friction Wheel LubricationCheck V-belts Engine Maintenance Service & Adjustments AdjustmentsService Drive Belt Friction Wheel RubberCarburetor Preparing Snow Thrower OFF-SEASON StoragePreparing Engine TROUBLE-SHOOTING Problem Possible Cause Corrective ActionParts List Polo Green Powder Black 80 17 Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Labels Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Key Description Qty Carburetor 900 Piston, & Pin Ass’y..010 OS Table from previous Recoil Starter Optional Garantia DE Información Especificaciones DEL ProductoPracticas Seguras DE Operacion EntrenamientoMantenimiento Y Almacenamiento Conjunto DE Ferreteria Piezas de RepuestoEnsamblado Fijacion Del Conjunto Del MangoFijacion De La Canaleta Fijacion De La Manivela De La CanaletaSoporte de la Fijacion De Los Gatillos De Giro Fijacion De La Vara De CambiosFijacion De Los Cables Del Embrague Cableado de la Lámpara Ajustes FinalesAjuste del Control de la Hélice Ajuste del Control del Propulsor de TracciónAjuste de la Zapata Deslizante Operacion Conozca Su Expulsor De NieveDetencion Del Expulsor De Nieve Para Expeler NieveAntes De Arrancar El Motor Para Arrancar El Motor Vea la FiguraLlene Con Gasolina Arrancador ElectricoPara Apagar El Motor Arranque En CalienteArrancador De Retroceso Arrancador De Retroceso CongeladoInstrucciones Abreviadas de Arranque Para Enganchar El PropulsorConsejos De Operacion Mantenimiento Recomendaciones GeneralesLubricacion Responsabilidades del clienteMantenimiento del Motor Vara De Cambios AjustesControl Del Propulsor De Traccion HelicesCorreas De La Helice CarburadorExtraccion Y Reemplazo De La Correa Placa Raspadoras Y Zapatas Deslizantes Goma De La Rueda De FriccionPreparación del Expulsor de Nieve Almacenamiento DE Fuera DE TemporadaPreparación del motor Problema Causas posible Accion Correctora Tabla DE Localizacion DE FallasYour Notes Comments contd Date HomeCentralSM
Top Page Image Contents