Craftsman 247.88855 owner manual Safe Operation Practices, Training

Page 3

SAFE OPERATION PRACTICES

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your snow thrower. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning.

Your snow thrower was built to be operated according to the rules for safe operation in this manual. As

DANGER:with any type of power equipment, carelessness or error on the part of the operator can result in serious

injury. If you violate any of these rules, you may cause serious injury to yourself or others.

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears Authorized Service Center (See the REPAIR PARTS section of this manual.)

TRAINING

Read this owner’s guide carefully in its entirety before attempting to assemble or operate this machine. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

Never allow children under 14 years old to operate a snow thrower. Children 14 years old and over should only operate a snow thrower under close parental supervision. Only persons well acquainted with these rules of safe operation should be allowed to use your snow thrower.

No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions.

Keep the area of operation clear of all persons, especially small children and pets.

Exercise caution to avoid slipping or falling, especially when operating in reverse.

PREPARATION

Thoroughly inspect the area where the equipment is to be used and remove all door mats, sleds, boards, wires and other foreign objects.

Do not operate equipment without wearing adequate outer garments for winter. Do not wear jewelry, long scarfs or other loose clothing which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

Before working with gasoline, extinguish all cigarettes and other sources of ignition. Check the fuel before starting the engine. Gasoline is an extremely flammable fuel. Do not fill the gasoline tank indoors, while the engine is running, or until engine has been allowed to cool at least two minutes. Replace

gasoline cap securely and wipe off any spilled gasoline before starting the engine as it may cause a fire or explosion.

Use a grounded three wire plug-in for all units with electric drive motors or electric starting motors.

Adjust collector housing height to clear gravel or crushed rock surface.

Never attempt to make any adjustments while engine is running (except where specifically recommended by manufacturer).

Let engine and machine adjust to outdoor temperature before starting to clear snow.

Always wear safety glasses or eye shields during operation or while performing an adjustment or repair, to protect eyes from foreign objects that may be thrown from the machine in any direction.

OPERATION

Do not put hands or feet near or under rotating parts. Keep clear of discharge opening and auger at all times.

Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

Do not carry passengers.

After striking a foreign object, stop the engine, remove wire from the spark plug and thoroughly inspect the snow thrower for any damage. Repair the damage before restarting and operating the snow thrower.

If the snow thrower starts to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble.

Stop the engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide and before making any repairs, adjustments, or inspections. Never place your

3

Image 3
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A 247.888550Warranty Information Table of ContentsTraining Safe Operation PracticesMaintenance and Storage Spare Part Hardware PackLoose Parts AssemblyAttaching Handle Assembly Removing From CartonAttaching Chute Crank Attaching ChuteNut Attaching Shift Rod Attaching Clutch CablesLamp Wiring Attaching Turn TriggersTrigger Cable Adjusting Skid Shoe Final AdjustmentsAdjusting Auger Control Adjusting Traction Drive ControlMeets Ansi Safety Standards OperationKnowing Your Snow Thrower To Stop The Snow Thrower Operating ControlsElectric Starter Before Starting EngineTo Start Engine Fill GasOperating Snow Thrower To Engage Augers To Throw SnowOperating Tips Before StoppingMaintenance General RecommendationsCustomer Responsibilities Lubrication Check V-beltsCheck Friction Wheel Engine Maintenance Adjustments Service & AdjustmentsService Friction Wheel Rubber Drive BeltCarburetor OFF-SEASON Storage Preparing EnginePreparing Snow Thrower Problem Possible Cause Corrective Action TROUBLE-SHOOTINGParts List Polo Green Powder Black 80 17 Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Labels Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Key Description Qty Carburetor 900 Piston, & Pin Ass’y..010 OS Table from previous Recoil Starter Optional Especificaciones DEL Producto Garantia DE InformaciónEntrenamiento Practicas Seguras DE OperacionMantenimiento Y Almacenamiento Piezas de Repuesto Conjunto DE FerreteriaFijacion Del Conjunto Del Mango EnsambladoFijacion De La Manivela De La Canaleta Fijacion De La CanaletaSoporte de la Fijacion De La Vara De Cambios Fijacion De Los Cables Del EmbragueFijacion De Los Gatillos De Giro Ajuste del Control del Propulsor de Tracción Cableado de la LámparaAjustes Finales Ajuste del Control de la HéliceAjuste de la Zapata Deslizante Conozca Su Expulsor De Nieve OperacionPara Expeler Nieve Detencion Del Expulsor De NieveArrancador Electrico Antes De Arrancar El MotorPara Arrancar El Motor Vea la Figura Llene Con GasolinaArrancador De Retroceso Congelado Para Apagar El MotorArranque En Caliente Arrancador De RetrocesoPara Enganchar El Propulsor Consejos De OperacionInstrucciones Abreviadas de Arranque Responsabilidades del cliente MantenimientoRecomendaciones Generales LubricacionMantenimiento del Motor Helices Vara De CambiosAjustes Control Del Propulsor De TraccionCarburador Extraccion Y Reemplazo De La CorreaCorreas De La Helice Goma De La Rueda De Friccion Placa Raspadoras Y Zapatas DeslizantesAlmacenamiento DE Fuera DE Temporada Preparación del motorPreparación del Expulsor de Nieve Tabla DE Localizacion DE Fallas Problema Causas posible Accion CorrectoraYour Notes Comments contd Date HomeCentralSM