Craftsman 247.88855 owner manual Nut

Page 8

Insert hex bolt through the upper chute crank bracket, handle panel support, and upper left handle. Secure the bracket using cupped washer and hex nut. Make sure that the cupped side of the washer is set against the contour of the handle.

 

Nut

Handle Panel

 

Washer

Support*

 

 

Hex Bolt

Upper Chute

Crank Bracket

* This part is already attached inside the handle panel

Figure 5

You may have to loosen the carriage bolts and hex lock nuts which secure the lower chute crank bracket to the extension on the left side of the chute assembly. See Figure 6.

Lower Chute

Carriage Bolt,

Hex Lock Nut

Crank Bracket

 

Figure 6

Place one 3/8 ID flat washer (from group G of the hardware pack) on the end of the chute crank, then insert the end of the crank into the eye hole in the plastic bushing in the chute crank bracket. See Figure 7.

Cotter Pin

Flat Washer

 

 

Chute Crank

Flat Washer

 

Lower Chute

 

Crank Bracket

Plastic Bushing

Figure 7

Place the other 3/8 ID flat washer (from the same group of hardware) on the end of the chute crank and insert hairpin clip into eye hole at the end of the chute crank. See Figure 7.

Slide the upper chute crank through the plastic bushing in the upper chute crank bracket and then into the lower chute crank. See Figure 8. Align the holes on the two pieces of the chute crank, and secure with hairpin clip from group C of the hardware pack.

Adjust the chute bracket so that the spiral on the chute crank fully engages the teeth on the chute assembly.

Using a wrench, tighten the hex bolt and the hex nut on the upper chute crank bracket.

Fully rotate the chute, using the chute crank, to make sure that it moves freely. Tighten the nuts on the lower chute crank bracket securely.

 

Hairpin Clip

Tilt

Upper

Chute

Chute

Cables

Crank

 

Upper

Chute

Crank

Bracket

Lower Chute

Crank

Figure 8

Slip the cables that run from the handle panel to the chute into the cable guide located on top of the engine. See Figure 9.

Cable Guide

Figure 9

8

Image 8
Contents 247.888550 Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.ATable of Contents Warranty InformationSafe Operation Practices TrainingMaintenance and Storage Hardware Pack Spare PartAssembly Attaching Handle AssemblyRemoving From Carton Loose PartsAttaching Chute Attaching Chute CrankNut Attaching Clutch Cables Attaching Shift RodTrigger Cable Lamp WiringAttaching Turn Triggers Final Adjustments Adjusting Auger ControlAdjusting Traction Drive Control Adjusting Skid ShoeKnowing Your Snow Thrower Meets Ansi Safety StandardsOperation Operating Controls To Stop The Snow ThrowerBefore Starting Engine To Start EngineFill Gas Electric StarterOperating Snow Thrower To Throw Snow Operating TipsBefore Stopping To Engage AugersCustomer Responsibilities MaintenanceGeneral Recommendations Check Friction Wheel LubricationCheck V-belts Engine Maintenance Service & Adjustments AdjustmentsService Drive Belt Friction Wheel RubberCarburetor Preparing Snow Thrower OFF-SEASON StoragePreparing Engine TROUBLE-SHOOTING Problem Possible Cause Corrective ActionParts List Polo Green Powder Black 80 17 Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Labels Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Key Description Qty Carburetor 900 Piston, & Pin Ass’y..010 OS Table from previous Recoil Starter Optional Garantia DE Información Especificaciones DEL ProductoPracticas Seguras DE Operacion EntrenamientoMantenimiento Y Almacenamiento Conjunto DE Ferreteria Piezas de RepuestoEnsamblado Fijacion Del Conjunto Del MangoFijacion De La Canaleta Fijacion De La Manivela De La CanaletaSoporte de la Fijacion De Los Gatillos De Giro Fijacion De La Vara De CambiosFijacion De Los Cables Del Embrague Cableado de la Lámpara Ajustes FinalesAjuste del Control de la Hélice Ajuste del Control del Propulsor de TracciónAjuste de la Zapata Deslizante Operacion Conozca Su Expulsor De NieveDetencion Del Expulsor De Nieve Para Expeler NieveAntes De Arrancar El Motor Para Arrancar El Motor Vea la FiguraLlene Con Gasolina Arrancador ElectricoPara Apagar El Motor Arranque En CalienteArrancador De Retroceso Arrancador De Retroceso CongeladoInstrucciones Abreviadas de Arranque Para Enganchar El PropulsorConsejos De Operacion Mantenimiento Recomendaciones GeneralesLubricacion Responsabilidades del clienteMantenimiento del Motor Vara De Cambios AjustesControl Del Propulsor De Traccion HelicesCorreas De La Helice CarburadorExtraccion Y Reemplazo De La Correa Placa Raspadoras Y Zapatas Deslizantes Goma De La Rueda De FriccionPreparación del Expulsor de Nieve Almacenamiento DE Fuera DE TemporadaPreparación del motor Problema Causas posible Accion Correctora Tabla DE Localizacion DE FallasYour Notes Comments contd Date HomeCentralSM