Craftsman 247.88855 owner manual Assembly, Removing From Carton, Loose Parts, Tools Required

Page 6

ASSEMBLY

Chute

Handle

 

 

Panel

Handles

Shift

Rod

Chute

Crank

Rear

Left

Right

Front

Electric

Start Cord

IMPORTANT: This unit is shipped with engine oil, but without gasoline, in the engine. After assembly, see OPERATION section of this manual for fuel selection and fill-up.

NOTE: To determine right and left hand sides of your snow thrower, stand behind the unit in the operator’s position. See Figure 1 inset.

Your snow thrower has been assembled at the factory, except the handle and the handle panel, the discharge chute assembly, the chute crank assembly and the shift rod. These parts are shipped loose in the carton.

Removing From Carton

Cut the corners of the carton and lay the sides flat on the ground. Remove all packing inserts.

Remove all loose parts. For a complete list of the loose parts, refer to the following section.

Move the snow thrower out of the carton.

Make certain all parts and literature have been removed before discarding the carton.

Loose Parts

(See Figure 1.)

a.Handle Panel & Chute Assembly

b.Right Hand & Left Hand Handles

Figure 1

c.Electric Start Cord

d.Two-Piece Chute Crank Assembly

e.Shift Rod

f.Hardware Pack

Assembly Tips: For easier assembly purposes, remove the chute from the carton and lay it on top of the engine. Do not unwrap the chute till you have installed the handle panel and the clutch cables.

Tools Required

1.1/2" , 7/16”, 3/8” wrenches or a set of adjustable wrenches

2.Set of standard head screw drivers

3.Set of philips head screw drivers

4.Funnel to fill up gasoline

WARNING: Make certain the spark plug wire is disconnected and moved away from the spark plug before assembling the snow thrower.

Attaching Handle Assembly

Stretch out control cables and place on the floor. Place the right handle in position with the flat side against the snow thrower. You can identify the right handle by the traction drive control label on it and the left handle by the auger clutch control label on it.

6

Image 6
Contents 247.888550 Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.ATable of Contents Warranty InformationSafe Operation Practices TrainingMaintenance and Storage Hardware Pack Spare PartRemoving From Carton AssemblyAttaching Handle Assembly Loose PartsAttaching Chute Attaching Chute CrankNut Attaching Clutch Cables Attaching Shift RodLamp Wiring Attaching Turn TriggersTrigger Cable Adjusting Traction Drive Control Final AdjustmentsAdjusting Auger Control Adjusting Skid ShoeMeets Ansi Safety Standards OperationKnowing Your Snow Thrower Operating Controls To Stop The Snow ThrowerFill Gas Before Starting EngineTo Start Engine Electric StarterOperating Snow Thrower Before Stopping To Throw SnowOperating Tips To Engage AugersMaintenance General RecommendationsCustomer Responsibilities Lubrication Check V-beltsCheck Friction Wheel Engine Maintenance Service & Adjustments AdjustmentsService Drive Belt Friction Wheel RubberCarburetor OFF-SEASON Storage Preparing EnginePreparing Snow Thrower TROUBLE-SHOOTING Problem Possible Cause Corrective ActionParts List Polo Green Powder Black 80 17 Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Labels Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Key Description Qty Carburetor 900 Piston, & Pin Ass’y..010 OS Table from previous Recoil Starter Optional Garantia DE Información Especificaciones DEL ProductoPracticas Seguras DE Operacion EntrenamientoMantenimiento Y Almacenamiento Conjunto DE Ferreteria Piezas de RepuestoEnsamblado Fijacion Del Conjunto Del MangoFijacion De La Canaleta Fijacion De La Manivela De La CanaletaSoporte de la Fijacion De La Vara De Cambios Fijacion De Los Cables Del EmbragueFijacion De Los Gatillos De Giro Ajuste del Control de la Hélice Cableado de la LámparaAjustes Finales Ajuste del Control del Propulsor de TracciónAjuste de la Zapata Deslizante Operacion Conozca Su Expulsor De NieveDetencion Del Expulsor De Nieve Para Expeler NieveLlene Con Gasolina Antes De Arrancar El MotorPara Arrancar El Motor Vea la Figura Arrancador ElectricoArrancador De Retroceso Para Apagar El MotorArranque En Caliente Arrancador De Retroceso CongeladoPara Enganchar El Propulsor Consejos De OperacionInstrucciones Abreviadas de Arranque Lubricacion MantenimientoRecomendaciones Generales Responsabilidades del clienteMantenimiento del Motor Control Del Propulsor De Traccion Vara De CambiosAjustes HelicesCarburador Extraccion Y Reemplazo De La CorreaCorreas De La Helice Placa Raspadoras Y Zapatas Deslizantes Goma De La Rueda De FriccionAlmacenamiento DE Fuera DE Temporada Preparación del motorPreparación del Expulsor de Nieve Problema Causas posible Accion Correctora Tabla DE Localizacion DE FallasYour Notes Comments contd Date HomeCentralSM