Craftsman 536.88626 Snow Chute Assembly, HOW to SET the Length of the Cables

Page 10

SNOW CHUTE ASSEMBLY

1.Turn crank assembly counterclock- wise until it stop.

2.Position snow chute on inside of

snow chute flange and align the three holes in the snow chute with

holes on snow chute flange. (See Figure 9)

3.Place three 5/16-18 carriage bolts from inside of chute as shown in

Figure 9. (hardware is found in parts bag).

4.Place three 5/16-18 flatwashers and three 5/16-18 nuts on outside of flange.

5.Tighten all four carriage bolts se- curely.

NOTE: DO NOT overtighten carriage bolts. ,.

HOW TO SET THE SKID HEIGHT

Your snow thrower is equipped with height adjust skids on the outside of the auger housing. To adjust the skid

6.Turn crank assembly clockwise and make sure all carriage bolts are tight.

Snow Chute

\

Flatwasher

Nut

__Carriage

"__Do

N _tlR:move

Flange

Hardware

 

Figure 9

height for different conditions, see To Adjust Skid Height paragraph in the Service And Adjustment section.

HOW TO SET THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments should be neces- sary. However, after the handles are put in the operating position, the cables can

be too tight or too loose. If an adjust- ment is necessary, see "How To Check And Adjust The Cables" in the Service And Adjustment section.

v- CHECKLIST

Before you operate your new snow thrower, to ensure that you receive the best performance and satisfaction from this quality product, please review the following checklist:

_" All assembly instructions have been completed.

_" The discharge chute rotates freely.

_" No remaining loose parts in carton.

While leaming how to use your snow thrower, pay extra attention to the fol- lowing important items:

_" Engine oil is at proper level.

_" Make sure gas tank is filled properly with clean, fresh, unleaded gasoline.

P" Become familiar with all controls- their location and function. Operate controls before starting engine.

F-001088J10

Image 10
Contents Snow Thrower 001088JWash Hands After Handling Training PreparationMaintenance and Storage Slow Fast Electric Start Engine Start Engine Run÷61 Drive Clutch Reverse Auger Clutch Auger Collector EngageNot actual size To Remove Snow Thrower From Carton Tools Required for AssemblyThrower ShifterLoosen To Assemble the Handle and Crank AssemblyRemove Short To Install Shifter KnobKnob LongHOW to SET the Skid Height Snow Chute AssemblyHOW to SET the Length of the Cables Position snow chute on insideChoke Control Used to start a cold Know Your Snow ThrowerDown To Control Snow Discharge HOW to Move Forward and BackwardTo Stop Your Snow Thrower To USE Wheel Lockout PINCheck the OIL Service & Adjustments section of this manualBefore Starting the Engine Fill GASTo Start Engine Equipped with a three-wireTo Stop Engine Cold StartCold Start Run engine at full throttle Fast when throwing snowWarm Start Warm StartSnow Throwing Tips Manual Lubrication ChartCustomer Responsibilities After Each USELUBRICATION-EVERY 25 Hours Product SpecificationsAS Required LUBRICATION-NOT RequiredTo Change Engine OIL EngineLubrication Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightTo Adjust Belts HOW to Check and Adjust CablesRemove the belt cover. See Outdoors, away from fire or Traction Drive BeltTo Replace Belts Auger DriveOutdoors, away from fire or Arning Drain the gasoline flame Pulley is properly aligned with the traction drive beltTraction DriveAuger If an adjustment is necessary, loos HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Is not in the correct position, adjust as followsHow To Replace The Friction Wheel Outdoors, away from fire orHOW to Replace the Auger Shear Bolt To Adjust or Replace the SparkplugTo adjust 001088J27 Snow Thrower OtherLine outdoors, away from Cause TroubleCorrection Craftsman 26 9HP Snow Thrower 536.886260 Frame Assembly DescriptionMotor Starter Electric Start AssemblyScrew Frame Assembly Frame AssyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Drive Flatwasher5OO Auger Housing Assembly500 544Auger Housing Assembly Craftsman 9HP Snow Thrower593 582 Craftsman 26 9HP Snow Thrower Discharge Chute Assembly PlasticHandle Assembly 725Washer Handle UpperWasher Sptlk Wheel Assembly 678 673Shift Yoke Assembly 8OO863 867 Chute Control ROD Assembly874 824 Decals828 831 View from AugerCraftsman 4-CYCLE Engine Model Number Gasket Craftsman 4-CYCLE Engine Model NumberKEY Part Description Piston, Pin & Ring SetIncl 29828820 EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.