Craftsman 536.88626 operating instructions Lubrication, To Change Engine OIL, Spark Plug

Page 19

drive plate or friction wheel come in

contact with grease or oil, damage to the friction wheel will result.

Should grease or oil come in contact with the disc drive plate or friction wheel, be sure to clean the plate and wheel thoroughly.

NOTE: For storage, the hex shaft and sprockets should be wiped with 5W30 motoroil to prevent rusting.

2.Auger Gear Box - The auger gear box is lubricated at the factory and should not require additional lubrica- tion. If for some reason the lubri- cant should leak out, have auger gear case checked by a competent repairman.

ENGINE

LUBRICATION

Check the crankcase oil level before starting the engine and after each five

(5)hours of continuous use. See Figure 17. Add S.A.E. 5W30 motor oil as needed. Tighten fill cap/dipstick se-

curely each time you check the oil lev- el.

Oil Fill Cap/Dipstick

tf

Figure 17

Change the oil every twenty-five(25) hours or at least once a year if the snow thrower is not used for twenty- five (25) hours.

TO CHANGE ENGINE OIL

1. Position the snow thrower so that the oil drain plug is at the lowest point on the engine.

2_ Remove the oil drain plug and the oil fill cap/dipstick. Drain the oil into a suitable container.

NOTE: The oil will drain more freely when the engine is warm.

. After draining all the oil, reinstall the oil drain plug securely.

4.Fill the engine crankcase with S.A.E. 5W30 motor oil, pouring slowly. DO NOT OVERFILL.

SPARK PLUG

Check the spark plug every twenty-

five (25) hours. Replace the spark plug if the electrodes are pitted or burned or if the porcelain is cracked.

1.Make sure the spark plug is clean. Clean the spark plug by carefully scraping the electrodes (do not sand blast or use a wire brush).

2.Check the spark plug gap with a feeler gauge and reset gap to 0.30" if necessary. See Figure 18.

3.Before installing the spark plug, coat the threads lightly with oil for easy removal. Tighten the spark plug to a torque of 15 foot-pounds.

Feeler Gauge 0.030"

Spark Plug

Figure 18

F-001088J19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 001088J Snow ThrowerWash Hands After Handling Preparation TrainingSlow Fast Electric Start Engine Start Engine Run Maintenance and StorageDrive Clutch Reverse Auger Clutch Auger Collector Engage ÷61Not actual size Shifter Tools Required for AssemblyThrower To Remove Snow Thrower From CartonLoosen To Assemble the Handle and Crank AssemblyRemove Long To Install Shifter KnobKnob ShortPosition snow chute on inside Snow Chute AssemblyHOW to SET the Length of the Cables HOW to SET the Skid HeightChoke Control Used to start a cold Know Your Snow ThrowerDown To USE Wheel Lockout PIN HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Control Snow DischargeFill GAS Service & Adjustments section of this manualBefore Starting the Engine Check the OILCold Start Equipped with a three-wireTo Stop Engine To Start EngineWarm Start Run engine at full throttle Fast when throwing snowWarm Start Cold StartSnow Throwing Tips After Each USE Lubrication ChartCustomer Responsibilities ManualLUBRICATION-NOT Required Product SpecificationsAS Required LUBRICATION-EVERY 25 HoursSpark Plug EngineLubrication To Change Engine OILTo Adjust Skid Height To Adjust Scraper BARTo Adjust Belts HOW to Check and Adjust CablesRemove the belt cover. See Auger Drive Traction Drive BeltTo Replace Belts Outdoors, away from fire orOutdoors, away from fire or Arning Drain the gasoline flame Pulley is properly aligned with the traction drive beltTraction DriveAuger Is not in the correct position, adjust as follows HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide If an adjustment is necessary, loosOutdoors, away from fire or How To Replace The Friction WheelHOW to Replace the Auger Shear Bolt To Adjust or Replace the SparkplugTo adjust 001088J27 Snow Thrower OtherLine outdoors, away from Cause TroubleCorrection Description Craftsman 26 9HP Snow Thrower 536.886260 Frame AssemblyMotor Starter Electric Start AssemblyScrew Frame Assy Frame AssemblyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Flatwasher Drive544 Auger Housing Assembly500 5OOCraftsman 9HP Snow Thrower Auger Housing Assembly593 582 Plastic Craftsman 26 9HP Snow Thrower Discharge Chute Assembly725 Handle AssemblyWasher Handle UpperWasher Sptlk 678 673 Wheel Assembly8OO Shift Yoke Assembly863 867 Chute Control ROD Assembly874 View from Auger Decals828 831 824Craftsman 4-CYCLE Engine Model Number Piston, Pin & Ring Set Craftsman 4-CYCLE Engine Model NumberKEY Part Description GasketIncl 29828820 EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.
Top Page Image Contents