Craftsman 536.88626 To Stop Engine, To Start Engine, Equipped with a three-wire, Cold Start

Page 14

Never use engine or carburetor cleaner

products in the fuel tank or permanent damage may occur.

1.Fill the fuel tank only with a fresh, clean, unleaded regular, unleaded premium, or reformulated automo- tive gasoline. DO NOT use leaded gasoline. Make sure that the con-

tainer you pour the gasoline from is clean and free from rust or other for-

eign particles. Never use gasoline that may be stale from long periods of storage in the container.

mable. Always use caution

AARNING: Gasoline is flam- when handling or storing

gasoline.

Do not fill fuel tank while snow thrower is running, when it is hot, or

when,snow thrower is in an en- closed area.

Keep away from open flame or an electrical spark and do not smoke while filling the fuel tank.

Never fill the tank completely. Fill the tank to within 1/4"-1/2" from the

top to provide space for expansion of fuel.

Always fill fuel tank outdoors and use a funnel or spout to prevent spilling.

Make sure to wipe up any spilled fuel before stating the engine. Store gasoline in a clean, approved container and keep the cap in place on the container.

TO STOP ENGINE

To stop engine, move the throttle con- trol lever to "STOP" position and re- move key. Keep the key in a safe place. The engine will not start without the key.

TO START ENGINE

(electric starter, if equipped)

Be sure that the engine has sufficient oil. The snow thrower engine is equipped with a 120 volt A.C. electric starter and recoil starter. Before start-

ing the engine, be certain that you have read the following information.

equipped with a three-wire

AARNING: The stader is power cord and plug and is

designed to operate on 120 volt AC household current.It must be proper- ly grounded at all times to avoid the possibility of electrical shock which may be injurious to operator. Follow all instructions carefully as set forth in the "To Start Engine" section. De- termine that your house wiring is a

three-wire grounded system. Ask a licensed electrician if you are not sure. If your house wire system is not a three-wire system, do not use this electric starter under any condi- tions. If your system is grounded and a three-hole receptacle is not available at the point your starter will normally be used, one should be installed by a licensed electrician. when connecting 120 volt AC "Power

Cord", always connect the cord to the Switch Box" on the engine first, then plug the other end into the three-hole grounded receptacle. When disconnecting "Power cord", always unplug the end in the three- hole grounded receptacle first.

COLD START

1.Be sure auger drive and traction drive levers are in the disengaged (RELEASED) position.

2.Move throttle control to"FAST" posi- tion.

3.Remove the keys form the plastic bag. Insert one key into ignition slot. Make sure it snaps into place. Do not turn key. Keep the second key in a safe place.

4.Rotate choke knob clockwise to the choke ON position.

5.Connect the power cord to the switch box on the engine.

6.Plug other end of power cord into a three-hole, grounded 120 VOLT, AC receptacle. (See WARNING in this section).

F-001088,.I14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Snow Thrower 001088JWash Hands After Handling Training PreparationMaintenance and Storage Slow Fast Electric Start Engine Start Engine Run÷61 Drive Clutch Reverse Auger Clutch Auger Collector EngageNot actual size To Remove Snow Thrower From Carton Tools Required for AssemblyThrower ShifterRemove To Assemble the Handle and Crank AssemblyLoosen Short To Install Shifter KnobKnob LongHOW to SET the Skid Height Snow Chute AssemblyHOW to SET the Length of the Cables Position snow chute on insideDown Know Your Snow ThrowerChoke Control Used to start a cold To Control Snow Discharge HOW to Move Forward and BackwardTo Stop Your Snow Thrower To USE Wheel Lockout PINCheck the OIL Service & Adjustments section of this manualBefore Starting the Engine Fill GASTo Start Engine Equipped with a three-wireTo Stop Engine Cold StartCold Start Run engine at full throttle Fast when throwing snowWarm Start Warm StartSnow Throwing Tips Manual Lubrication ChartCustomer Responsibilities After Each USELUBRICATION-EVERY 25 Hours Product SpecificationsAS Required LUBRICATION-NOT RequiredTo Change Engine OIL EngineLubrication Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightRemove the belt cover. See HOW to Check and Adjust CablesTo Adjust Belts Outdoors, away from fire or Traction Drive BeltTo Replace Belts Auger DriveTraction DriveAuger Pulley is properly aligned with the traction drive beltOutdoors, away from fire or Arning Drain the gasoline flame If an adjustment is necessary, loos HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Is not in the correct position, adjust as followsHow To Replace The Friction Wheel Outdoors, away from fire orTo adjust To Adjust or Replace the SparkplugHOW to Replace the Auger Shear Bolt 001088J27 Line outdoors, away from OtherSnow Thrower Correction TroubleCause Craftsman 26 9HP Snow Thrower 536.886260 Frame Assembly DescriptionScrew Electric Start AssemblyMotor Starter Frame Assembly Frame AssyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Drive Flatwasher5OO Auger Housing Assembly500 544Auger Housing Assembly Craftsman 9HP Snow Thrower593 582 Craftsman 26 9HP Snow Thrower Discharge Chute Assembly PlasticHandle Assembly 725Washer Sptlk Handle UpperWasher Wheel Assembly 678 673Shift Yoke Assembly 8OO874 Chute Control ROD Assembly863 867 824 Decals828 831 View from AugerCraftsman 4-CYCLE Engine Model Number Gasket Craftsman 4-CYCLE Engine Model NumberKEY Part Description Piston, Pin & Ring Set28820 298Incl EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.
Top Page Image Contents