Craftsman 536.88626 To Assemble the Handle and Crank Assembly, Loosen, Remove

Page 8

2.Remove and discardthe packing material from around the snow thrower.

3.Cut down all four corners of the car- ton and lay the panels flat.

4.Rollsnow thrower off the carton by

pulling on the lower handle. CAU- TION: DO NOT back over cables.

5.Remove the packing materialfrom handle assembly.

6.Cut ties securing the clutch control cables to the lower handle and lay

cable back away from the motor frame.

TO ASSEMBLE THE HANDLE AND CRANK ASSEMBLY

1.Cut tie holding shift rod to lower handle and move shifter to the first

forward gear.

2.Loosen, but do not remove, the screws, flatwashers, Iockwashers, and hex nuts in the upper holes of the lower handle. See Figure 3.

Right Hand Side

Ofl

Loosen,

but do not

remove

11132" Flatwasher

5/16" Hex

5/16" Screw

5/16" Split

Loekwasher

Figure 3

NOTE: Make sure the cables are not

caught between the upper and lower handle.

3.Raise the upper handle into operat- ing position. Upper handle should be to the outside of the lower han- dle.

NOTE: If the cables have become dis- connected form the clutch levers, rein- stall the cables as shown in Figure 4.

NOTE: Position cable through slots on shifter plate.

Clutch Lever

"Z"

Fitting

/

Control

_.

..,./

Cable _(_/

Figure 4

4.Install hardware supplied in the parts bag (screw, flatwasher, lock- washer, and hex nut) into bottom hole on right hand side of handles. DO NOT tighten until all bolts are in p_ace.

5.Locate crank assembly removed earlier and remove the nylon lock- nut and flatwasher from the eye bolt assembly. See Figure 5.

Left Hand Side Of

Upper Handle

 

 

3/8" Nylon

\

/

Locknut

 

 

3/8"

Eye Bolt

 

Flatwasher

3/8"

Flatwasher

 

 

Figure 5

. Reinstall fiatwasher and adaptor. Install eye bolt through lower hole on the left hand side of the handle.

F-001088J8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Snow Thrower 001088JWash Hands After Handling Training PreparationMaintenance and Storage Slow Fast Electric Start Engine Start Engine Run÷61 Drive Clutch Reverse Auger Clutch Auger Collector EngageNot actual size Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton ShifterRemove To Assemble the Handle and Crank AssemblyLoosen To Install Shifter Knob KnobShort LongSnow Chute Assembly HOW to SET the Length of the CablesHOW to SET the Skid Height Position snow chute on insideDown Know Your Snow ThrowerChoke Control Used to start a cold HOW to Move Forward and Backward To Stop Your Snow ThrowerTo Control Snow Discharge To USE Wheel Lockout PINService & Adjustments section of this manual Before Starting the EngineCheck the OIL Fill GASEquipped with a three-wire To Stop EngineTo Start Engine Cold StartRun engine at full throttle Fast when throwing snow Warm StartCold Start Warm StartSnow Throwing Tips Lubrication Chart Customer ResponsibilitiesManual After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours LUBRICATION-NOT RequiredEngine LubricationTo Change Engine OIL Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightRemove the belt cover. See HOW to Check and Adjust CablesTo Adjust Belts Traction Drive Belt To Replace BeltsOutdoors, away from fire or Auger DriveTraction DriveAuger Pulley is properly aligned with the traction drive beltOutdoors, away from fire or Arning Drain the gasoline flame HOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideIf an adjustment is necessary, loos Is not in the correct position, adjust as followsHow To Replace The Friction Wheel Outdoors, away from fire orTo adjust To Adjust or Replace the SparkplugHOW to Replace the Auger Shear Bolt 001088J27 Line outdoors, away from OtherSnow Thrower Correction TroubleCause Craftsman 26 9HP Snow Thrower 536.886260 Frame Assembly DescriptionScrew Electric Start AssemblyMotor Starter Frame Assembly Frame AssyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Drive FlatwasherAuger Housing Assembly 5005OO 544Auger Housing Assembly Craftsman 9HP Snow Thrower593 582 Craftsman 26 9HP Snow Thrower Discharge Chute Assembly PlasticHandle Assembly 725Washer Sptlk Handle UpperWasher Wheel Assembly 678 673Shift Yoke Assembly 8OO874 Chute Control ROD Assembly863 867 Decals 828 831824 View from AugerCraftsman 4-CYCLE Engine Model Number Craftsman 4-CYCLE Engine Model Number KEY Part DescriptionGasket Piston, Pin & Ring Set28820 298Incl EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.
Top Page Image Contents