Craftsman 536.88626 HOW to Adjust or Replace the Friction Wheel, HOW to Adjust the Belt Guide

Page 24

HOW TO ADJUST THE BELT GUIDE

1.Disconnect spark plug wire.

2.Remove the screw. Remove the belt cover. See Figure 22.

3.Engage the auger drive lever.

4.Measure the distance between the belt guide and auger drive belt. The correct distance is 1/8 inch (3.175 mm). See Figure 27.

A WARNING: Drain the gasoline outdoors, away from fire or

flame.

2.Disconnect the spark plug wire.

3.Remove the bolts on each side of

the bottom panel. See Figure 28.

. Loosen the bolts on each side of the bottom panel.

. Remove the bottom panel.

Remove Top Bolt (each side)

_

Belt Guide

Auger _ -_°_l/81nch

Idler /_ - "_\" (3.175 ram)

Pu,ey \\

Engagedi ___. "

Figure27

. If an adjustment is necessary, loos-

\

Motet

Mount

Frame

Loosen bottom bolts _

(Each Side)

6.Position the shift speed the first forward gear.

Bottom

Panel

Auger

Housing

Figure 28

lever in

en the mounting bolt for the belt guide. Move the belt guide to the correct position. Tighten the mounting bolt for the belt guide.

6.Install the belt cover. Tighten the screw. See Figure 22.

7.Connect the spark plug wire.

HOW TO ADJUST OR REPLACE THE FRICTION WHEEL

How To Check The Friction Wheel If the snow thrower will not move for- ward, check the traction drive belt, the traction drive cable or the friction wheel. If the friction wheel is worn or damaged, it must be replaced. See "How To Re- place the Friction Wheel" in this section. If the friction wheel is not worn or dam- aged, check as follows.

1.Remove the gas from the gas tank. Stand the snow thrower up on the front end of the auger housing.

7.Note the position of the friction wheel on the disc drive plate (See Figure 29). In the correct position, the right outer side of the disc drive plate must be three inches

(7,62cm.) from the center of the friction wheel. If the friction wheel

is not in the correct position, adjust as follows.

Friction

Wheel

I

Drive

Plate

>

Figure 29

How To Adjust The Friction Wheel

1.Loosen the bolts on the speed control rod to optain the correct

F-001088J24

Image 24
Contents Snow Thrower 001088JWash Hands After Handling Training PreparationMaintenance and Storage Slow Fast Electric Start Engine Start Engine Run÷61 Drive Clutch Reverse Auger Clutch Auger Collector EngageNot actual size Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton ShifterTo Assemble the Handle and Crank Assembly LoosenRemove To Install Shifter Knob KnobShort LongSnow Chute Assembly HOW to SET the Length of the CablesHOW to SET the Skid Height Position snow chute on insideKnow Your Snow Thrower Choke Control Used to start a coldDown HOW to Move Forward and Backward To Stop Your Snow ThrowerTo Control Snow Discharge To USE Wheel Lockout PINService & Adjustments section of this manual Before Starting the EngineCheck the OIL Fill GASEquipped with a three-wire To Stop EngineTo Start Engine Cold StartRun engine at full throttle Fast when throwing snow Warm StartCold Start Warm StartSnow Throwing Tips Lubrication Chart Customer ResponsibilitiesManual After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours LUBRICATION-NOT RequiredEngine LubricationTo Change Engine OIL Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightHOW to Check and Adjust Cables To Adjust BeltsRemove the belt cover. See Traction Drive Belt To Replace BeltsOutdoors, away from fire or Auger DrivePulley is properly aligned with the traction drive belt Outdoors, away from fire or Arning Drain the gasoline flameTraction DriveAuger HOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideIf an adjustment is necessary, loos Is not in the correct position, adjust as followsHow To Replace The Friction Wheel Outdoors, away from fire orTo Adjust or Replace the Sparkplug HOW to Replace the Auger Shear BoltTo adjust 001088J27 Other Snow ThrowerLine outdoors, away from Trouble CauseCorrection Craftsman 26 9HP Snow Thrower 536.886260 Frame Assembly DescriptionElectric Start Assembly Motor StarterScrew Frame Assembly Frame AssyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Drive FlatwasherAuger Housing Assembly 5005OO 544Auger Housing Assembly Craftsman 9HP Snow Thrower593 582 Craftsman 26 9HP Snow Thrower Discharge Chute Assembly PlasticHandle Assembly 725Handle Upper WasherWasher Sptlk Wheel Assembly 678 673Shift Yoke Assembly 8OOChute Control ROD Assembly 863 867874 Decals 828 831824 View from AugerCraftsman 4-CYCLE Engine Model Number Craftsman 4-CYCLE Engine Model Number KEY Part DescriptionGasket Piston, Pin & Ring Set298 Incl28820 EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.