Craftsman 536.88626 operating instructions Wheel Assembly, 678 673

Page 42

CRAFTSMAN 26" 9HP SNOW THROWER 536.886260

WHEEL ASSEMBLY

678

673

673

"""

Key No.

Description

650SHAFT, AXLE

652SPRKT & HUB

653SCREW, 1/4-20X2.25

654NUT, 1/4-20 HEX NYLOCK

655BRNG, FL

656CHAIN, ROLLER

LINK, CHAIN MASTER

671FLATVVASHER .765X1.12X.06

673	BUSHING, WHEEL
675	TIRE	& RIM
676	SCREW, 1/4-20X1.75 HH
677	NUT,	1/4-20 HEX NYLOCK
678	RING,	RET
679	PIN, KLIK .25 X 1.38 DIA
F-001088.1		42

318542

Part No.

580883

583012

73839

780029

581730

579867

760504

712120

585591

318504

577015

780029

239

73842

Image 42

Contents Snow Thrower 001088JWash Hands After Handling Training PreparationMaintenance and Storage Slow Fast Electric Start Engine Start Engine Run÷61 Drive Clutch Reverse Auger Clutch Auger Collector EngageNot actual size To Remove Snow Thrower From Carton Tools Required for AssemblyThrower ShifterTo Assemble the Handle and Crank Assembly LoosenRemove Short To Install Shifter KnobKnob LongHOW to SET the Skid Height Snow Chute AssemblyHOW to SET the Length of the Cables Position snow chute on insideKnow Your Snow Thrower Choke Control Used to start a coldDown To Control Snow Discharge HOW to Move Forward and BackwardTo Stop Your Snow Thrower To USE Wheel Lockout PINCheck the OIL Service & Adjustments section of this manualBefore Starting the Engine Fill GASTo Start Engine Equipped with a three-wireTo Stop Engine Cold StartCold Start Run engine at full throttle Fast when throwing snowWarm Start Warm StartSnow Throwing Tips Manual Lubrication ChartCustomer Responsibilities After Each USELUBRICATION-EVERY 25 Hours Product SpecificationsAS Required LUBRICATION-NOT RequiredTo Change Engine OIL EngineLubrication Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightHOW to Check and Adjust Cables To Adjust BeltsRemove the belt cover. See Outdoors, away from fire or Traction Drive BeltTo Replace Belts Auger DrivePulley is properly aligned with the traction drive belt Outdoors, away from fire or Arning Drain the gasoline flameTraction DriveAuger If an adjustment is necessary, loos HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Is not in the correct position, adjust as followsHow To Replace The Friction Wheel Outdoors, away from fire orTo Adjust or Replace the Sparkplug HOW to Replace the Auger Shear BoltTo adjust 001088J27 Other Snow ThrowerLine outdoors, away from Trouble CauseCorrection Craftsman 26 9HP Snow Thrower 536.886260 Frame Assembly DescriptionElectric Start Assembly Motor StarterScrew Frame Assembly Frame AssyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Drive Flatwasher5OO Auger Housing Assembly500 544Auger Housing Assembly Craftsman 9HP Snow Thrower593 582 Craftsman 26 9HP Snow Thrower Discharge Chute Assembly PlasticHandle Assembly 725Handle Upper WasherWasher Sptlk Wheel Assembly 678 673Shift Yoke Assembly 8OOChute Control ROD Assembly 863 867874 824 Decals828 831 View from AugerCraftsman 4-CYCLE Engine Model Number Gasket Craftsman 4-CYCLE Engine Model NumberKEY Part Description Piston, Pin & Ring Set298 Incl28820 EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8