Craftsman 536.88626 Warm Start, Cold Start, Run engine at full throttle Fast when throwing snow

Page 15

. Push the primer button while cov- ering the vent hole as follows: Re- move finger from primer button between primes.

Do not prime if temperature above 50 ° F (10 ° C).

Push two time if temperature is 50 ° F (10 ° C) to 15°F (-10 ° C).

Push four times if temperature is below 15° F (-10 ° C).

8.Push down on the starter button

until the engine starts. Do not crank for more than 10 seconds at a time.

This electric starter is thermally pro- tected. If overheated it will stop au- tomatically and can be restarted only when it has cooled to a safe temperature (a wait of about 5 to 10 minutes is required).

9.When the engine starts, release the starter button and move choke le- ver to "1/2 choke" position. When

engine runs smoothly, move choke lever to "No Choke" Position.

10.Disconnect power cord from recep- tacle, first, and then from switch box.

NOTE: Allow the engine to warm up for several minutes before blowing snow in temperatures below 0°F.

11.Run engine at full throttle "FAST' when throwing snow.

WARM START

If restarting a warm engine after a short shutdown, leave choke at "OFF" and do not push the primer button. If the en- gine fails to start, follow the Cold Start instructions.

TO START ENGINE

(recoil starter)

Be sure that the engine has sufficient oil. The snow thrower engine is equipped with a recoil starter. Before starting the engine, be certain that you have read the following information.

COLD START

1.Be sure auger drive and traction drive levers are in the disengaged

(RELEASED) position.

2.Move throttle control to"FAST' posi- tion.

3.Remove the keys form the plastic bag. Insert one key into ignition slot. Make sure it snaps into place. Do not turn key. Keep the second key in a safe place.

4.Rotate choke knob clockwise to the choke ON position.

5.Push the primer button while cov- ering the vent hole as follows: Re- move finger from primer button between primes.

Do not prime if temperature above 50 ° F (10 ° C).

Push two time if temperature is 50 ° F (10 ° C) to 15°F (-10 ° C).

Push four times if temperature is below 15° F (-10 ° C).

6.Pull the starter handle rapidly. Do not allow the handle to snap back, but allow it to rewind slowly while

keeping a firm hold on the starter handle.

7.As the engine warms up, move choke lever to "1/2 choke" position.

When engine runs smoothly, move choke lever to "No Choke" Posi-

tion.

NOTE: Allow the engine to warm up for several minutes before blowing snow in temperatures below 0°E

8.Run engine at full throttle "FAST' when throwing snow.

WARM START

If restarting a warm engine after a short shutdown, leave choke at "OFF" and do not push the primer button. If the en- gine fails to start, follow the Cold Start instructions.

FROZEN STARTER

If the starter is frozen and will not turn engine:

1.Pull as much rope out of the starter as possible.

F-001088J15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 001088J Snow ThrowerWash Hands After Handling Preparation TrainingSlow Fast Electric Start Engine Start Engine Run Maintenance and StorageDrive Clutch Reverse Auger Clutch Auger Collector Engage ÷61Not actual size Shifter Tools Required for AssemblyThrower To Remove Snow Thrower From CartonTo Assemble the Handle and Crank Assembly LoosenRemove Long To Install Shifter KnobKnob ShortPosition snow chute on inside Snow Chute AssemblyHOW to SET the Length of the Cables HOW to SET the Skid HeightKnow Your Snow Thrower Choke Control Used to start a coldDown To USE Wheel Lockout PIN HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Control Snow DischargeFill GAS Service & Adjustments section of this manualBefore Starting the Engine Check the OILCold Start Equipped with a three-wireTo Stop Engine To Start EngineWarm Start Run engine at full throttle Fast when throwing snowWarm Start Cold StartSnow Throwing Tips After Each USE Lubrication ChartCustomer Responsibilities ManualLUBRICATION-NOT Required Product SpecificationsAS Required LUBRICATION-EVERY 25 HoursSpark Plug EngineLubrication To Change Engine OILTo Adjust Skid Height To Adjust Scraper BARHOW to Check and Adjust Cables To Adjust BeltsRemove the belt cover. See Auger Drive Traction Drive BeltTo Replace Belts Outdoors, away from fire orPulley is properly aligned with the traction drive belt Outdoors, away from fire or Arning Drain the gasoline flameTraction DriveAuger Is not in the correct position, adjust as follows HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide If an adjustment is necessary, loosOutdoors, away from fire or How To Replace The Friction WheelTo Adjust or Replace the Sparkplug HOW to Replace the Auger Shear BoltTo adjust 001088J27 Other Snow ThrowerLine outdoors, away from Trouble CauseCorrection Description Craftsman 26 9HP Snow Thrower 536.886260 Frame AssemblyElectric Start Assembly Motor StarterScrew Frame Assy Frame AssemblyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Flatwasher Drive544 Auger Housing Assembly500 5OOCraftsman 9HP Snow Thrower Auger Housing Assembly593 582 Plastic Craftsman 26 9HP Snow Thrower Discharge Chute Assembly725 Handle AssemblyHandle Upper WasherWasher Sptlk 678 673 Wheel Assembly8OO Shift Yoke AssemblyChute Control ROD Assembly 863 867874 View from Auger Decals828 831 824Craftsman 4-CYCLE Engine Model Number Piston, Pin & Ring Set Craftsman 4-CYCLE Engine Model NumberKEY Part Description Gasket298 Incl28820 EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.
Top Page Image Contents