Craftsman 536.88626 operating instructions To Adjust Scraper BAR, To Adjust Skid Height

Page 20

nect the spark plug wire and

,_ WARNING: Always discon- place it where it cannot

make contact with spark plug to pre- vent accidental starting when mak- ing any adjustments or repairs.

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two height adjustment skids, located on the outside of the auger housing. See Figure 19.

These skids elevate the front of the snow thrower.

Mountin_ Nuts

,. O

Auger Housmg Height Adjust Skid

Figure 19

For normal hard surfaces, such as a

paved driveway or walk, adjust the skids as follows.

1.Position the snow thrower on a level surface.

2.Make sure both tires are equally in- flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi- mum inflation. Do not exceed side- wall maximum pressure on tire.

3.Place the extra shear bolts supplied (found in parts bag) under each end of the scraper bar next to the adjustable skids.

4.Loosen the mounting nuts that hold the adjustable skids. To bring the front of the snow thrower down,

raise the adjustable skids. Tighten the mounting nuts. See Figure 19.

NOTE: For rocky or uneven surfaces, raise the front of the snow thrower by moving the skids down.

maintain proper ground

,_ WARNING: Be certain to clearance for your particular

area to be cleared. Objects such as gravel, rocks or other debris, if struck by the impeller, may be thrown with sufficient force to cause

personal injury, property damage or damage to the snow thrower.

TO ADJUST SCRAPER BAR

After considerable use, the metal scrap- er bar will have a definite wear pattern. The scraper bar in conjunction with the skids should always be adjusted to al-

low 1/8" between the scraper bar and the sidewalk or area to be cleaned.

. Position the snow thrower on a level surface.

2.Make sure both tires are equally in- flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi- mum inflation. Do not exceed side-

wall maximum pressure on tire.

3.Loosen the carriage bolts and nuts securing the scraper bar to the au- ger housing.

4.Adjust the scraper bar to the proper position.

5.Tighten the carriage bolts and nuts, making sure that the scraper bar is parallel with the working surface.

. For extended operation, the scraper bar may be reversed. If the scraper bar must be replaced due to wear, remove the carriage bolts and nuts and install a new scraper bar.

F-001088J

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Snow Thrower 001088JWash Hands After Handling Training PreparationMaintenance and Storage Slow Fast Electric Start Engine Start Engine Run÷61 Drive Clutch Reverse Auger Clutch Auger Collector EngageNot actual size Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton ShifterRemove To Assemble the Handle and Crank AssemblyLoosen To Install Shifter Knob KnobShort LongSnow Chute Assembly HOW to SET the Length of the CablesHOW to SET the Skid Height Position snow chute on insideDown Know Your Snow ThrowerChoke Control Used to start a cold HOW to Move Forward and Backward To Stop Your Snow ThrowerTo Control Snow Discharge To USE Wheel Lockout PINService & Adjustments section of this manual Before Starting the EngineCheck the OIL Fill GASEquipped with a three-wire To Stop EngineTo Start Engine Cold StartRun engine at full throttle Fast when throwing snow Warm StartCold Start Warm StartSnow Throwing Tips Lubrication Chart Customer ResponsibilitiesManual After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours LUBRICATION-NOT RequiredEngine LubricationTo Change Engine OIL Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightRemove the belt cover. See HOW to Check and Adjust CablesTo Adjust Belts Traction Drive Belt To Replace BeltsOutdoors, away from fire or Auger DriveTraction DriveAuger Pulley is properly aligned with the traction drive beltOutdoors, away from fire or Arning Drain the gasoline flame HOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideIf an adjustment is necessary, loos Is not in the correct position, adjust as followsHow To Replace The Friction Wheel Outdoors, away from fire orTo adjust To Adjust or Replace the SparkplugHOW to Replace the Auger Shear Bolt 001088J27 Line outdoors, away from OtherSnow Thrower Correction TroubleCause Craftsman 26 9HP Snow Thrower 536.886260 Frame Assembly DescriptionScrew Electric Start AssemblyMotor Starter Frame Assembly Frame AssyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Drive FlatwasherAuger Housing Assembly 5005OO 544Auger Housing Assembly Craftsman 9HP Snow Thrower593 582 Craftsman 26 9HP Snow Thrower Discharge Chute Assembly PlasticHandle Assembly 725Washer Sptlk Handle UpperWasher Wheel Assembly 678 673Shift Yoke Assembly 8OO874 Chute Control ROD Assembly863 867 Decals 828 831824 View from AugerCraftsman 4-CYCLE Engine Model Number Craftsman 4-CYCLE Engine Model Number KEY Part DescriptionGasket Piston, Pin & Ring Set28820 298Incl EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.
Top Page Image Contents