Craftsman 536.88626 How To Replace The Friction Wheel, Outdoors, away from fire or

Page 25

position for the friction wheel. See Figure 30.

Leverl _Spring _ _,@ / -"J

Figure 30

2.Install the bottom panel. See Figure 28.

3.Tighte_ the bolts on each side of the bottom panel.

4.Install the bolts on each side of the bottom panel.

How To Replace The Friction Wheel

If the friction wheel is worn or damaged, the snow thrower will not move forward.

The friction wheel must be replaced as follows.

1.Remove the gas from the gas tank. Stand the snow thrower up on the front end of the auger housing.

outdoors, away from fire or

,_ WARNING: Drain the gasoline flame.

2.Disconnect the spark plug wire.

3.Remove the top bolts on each side of the bottom panel. See

Figure 28.

4.Loosen the bottom bolts on each side of the bottom panel.

5.Remove the bottom panel.

6.Remove the three fasteners that hold the friction wheel to the hub.

See Figure 31.

Hub

Bolt

HexNut

Shaft

Figure 31

7.Remove the four bolts that hold the bearing plates on each side of the hex shaft. See Figure 32.

NOTE: Take special note of the position of the washers and retain- ing ring on the hex shaft and the sprocket assembly.

Friction Wheel Hex Shaft

Bearing

Bearing

Plate

Plate

Figure32

8.Remove the bearing plate from the right side. Do not remove the hex shaft. Leave the hex shaft in posi- tion. Carefully raise hex shaft just

enough to allow the friction wheel to be removed.

9.Remove the friction wheel from the

hub. Slip the friction wheel toward the right off the hex shaft. See

Figure 31.

10.Assemble the new friction wheel onto hub with the fasteners re- moved earlier.

11.Install the bearing plate onto the right side. Make sure the hex shaft is engaged with both bearing plates and that the washers and re- taining ring are installed in the origi- nal position. See Figure 32.

F-001088,.I25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 001088J Snow ThrowerWash Hands After Handling Preparation TrainingSlow Fast Electric Start Engine Start Engine Run Maintenance and StorageDrive Clutch Reverse Auger Clutch Auger Collector Engage ÷61Not actual size Thrower Tools Required for AssemblyTo Remove Snow Thrower From Carton ShifterLoosen To Assemble the Handle and Crank AssemblyRemove Knob To Install Shifter KnobShort LongHOW to SET the Length of the Cables Snow Chute AssemblyHOW to SET the Skid Height Position snow chute on insideChoke Control Used to start a cold Know Your Snow ThrowerDown To Stop Your Snow Thrower HOW to Move Forward and BackwardTo Control Snow Discharge To USE Wheel Lockout PINBefore Starting the Engine Service & Adjustments section of this manualCheck the OIL Fill GASTo Stop Engine Equipped with a three-wireTo Start Engine Cold StartWarm Start Run engine at full throttle Fast when throwing snowCold Start Warm StartSnow Throwing Tips Customer Responsibilities Lubrication ChartManual After Each USEAS Required Product SpecificationsLUBRICATION-EVERY 25 Hours LUBRICATION-NOT RequiredLubrication EngineTo Change Engine OIL Spark PlugTo Adjust Skid Height To Adjust Scraper BARTo Adjust Belts HOW to Check and Adjust CablesRemove the belt cover. See To Replace Belts Traction Drive BeltOutdoors, away from fire or Auger DriveOutdoors, away from fire or Arning Drain the gasoline flame Pulley is properly aligned with the traction drive beltTraction DriveAuger HOW to Adjust the Belt Guide HOW to Adjust or Replace the Friction WheelIf an adjustment is necessary, loos Is not in the correct position, adjust as followsOutdoors, away from fire or How To Replace The Friction WheelHOW to Replace the Auger Shear Bolt To Adjust or Replace the SparkplugTo adjust 001088J27 Snow Thrower OtherLine outdoors, away from Cause TroubleCorrection Description Craftsman 26 9HP Snow Thrower 536.886260 Frame AssemblyMotor Starter Electric Start AssemblyScrew Frame Assy Frame AssemblyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Flatwasher Drive500 Auger Housing Assembly5OO 544Craftsman 9HP Snow Thrower Auger Housing Assembly593 582 Plastic Craftsman 26 9HP Snow Thrower Discharge Chute Assembly725 Handle AssemblyWasher Handle UpperWasher Sptlk 678 673 Wheel Assembly8OO Shift Yoke Assembly863 867 Chute Control ROD Assembly874 828 831 Decals824 View from AugerCraftsman 4-CYCLE Engine Model Number KEY Part Description Craftsman 4-CYCLE Engine Model NumberGasket Piston, Pin & Ring SetIncl 29828820 EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.
Top Page Image Contents