Craftsman 536.88626 Pulley is properly aligned with the traction drive belt, Traction DriveAuger

Page 23

. Remove the old auger drive belt.

Replace the auger drive belt with

an original factory replacement belt available from an authorized service

center.

9.install the new auger drive belt onto the auger drive pulley and onto the drive pulley,

10.Adjust the auger drive belt. See "How To Adjust The Auger Drive

Belt" in the Service And Adjustment section.

11.Adjust the belt guide. See "How To Adjust The Belt Guide" in the Ser- vice And Adjustment section.

12.Install the bolts on each side of the motor mount frame. See

Figure 25.

13.Tighter_the bolts on each side of the motor mount frame.

14.Install the belt cover. Tighten the screw. See Figure 22.

15.Check the adjustment of the cables. See "How To Check And Adjust The

Cables" in the Service And Adjust- ment section.

16.Connect the spark plug wire.

How To Remove the Traction Drive Belt

If the snow thrower will not move for- ward, check the traction drive belt for wear or damage. If the traction drive belt is worn or damaged, replace the belt as follows.

1.Remove the gas from the gas tank. Stand the snow thrower up on the front end of the auger housing.

outdoors, away from fire or

_ARNING: Drain the gasoline flame.

2.Disconnect the spark plug wire.

3.Remove the auger drive belt. See "How To Remove The Auger Drive Belt" in the Maintenance section.

4.Pull the traction drive idler pulley away from the traction drive belt. See Figure 26.

Traction Drive Belt

Auger Drive

Traction

Belt Guide

Drive Pulley

Auger

Drive

Pulley

Traction

DriveAuger

IdlerIdler

PulleyPulley

Engine Pulley

Figure 26

. Remove the old traction drive belt from the traction drive pulley and from the engine pulley. Replace the traction drive belt with an original

factory replacement belt available from an authorized service center.

. Install the new traction drive belt onto the traction drive pulley and onto the engine pulley.

. Make sure the traction drive idler

pulley is properly aligned with the traction drive belt.

. Install and adjust the auger drive belt. See "How To Remove The Au-

ger Drive Belt" in the Service And Adjustment section.

. Adjust the belt guide. See "How To Adjust The Belt Guide" in the Ser- vice And Adjustment section.

10.Install the bolts on each side of the motor mount frame. See Figure 25.

11.Tighten the bolts on each side of the motor mount frame.

12.Install the belt cover. Tighten screw. See Figure 22.

13.Check the adjustment of the cables. See "How To Check And Adjust The

Cables" in the Service And Adjust- ment section.

14.Connect the spark plug wire.

F-001088J23

Image 23
Contents 001088J Snow ThrowerWash Hands After Handling Preparation TrainingSlow Fast Electric Start Engine Start Engine Run Maintenance and StorageDrive Clutch Reverse Auger Clutch Auger Collector Engage ÷61Not actual size Shifter Tools Required for AssemblyThrower To Remove Snow Thrower From CartonRemove To Assemble the Handle and Crank AssemblyLoosen Long To Install Shifter KnobKnob ShortPosition snow chute on inside Snow Chute AssemblyHOW to SET the Length of the Cables HOW to SET the Skid HeightDown Know Your Snow ThrowerChoke Control Used to start a cold To USE Wheel Lockout PIN HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Control Snow DischargeFill GAS Service & Adjustments section of this manualBefore Starting the Engine Check the OILCold Start Equipped with a three-wireTo Stop Engine To Start EngineWarm Start Run engine at full throttle Fast when throwing snowWarm Start Cold StartSnow Throwing Tips After Each USE Lubrication ChartCustomer Responsibilities ManualLUBRICATION-NOT Required Product SpecificationsAS Required LUBRICATION-EVERY 25 HoursSpark Plug EngineLubrication To Change Engine OILTo Adjust Skid Height To Adjust Scraper BARRemove the belt cover. See HOW to Check and Adjust CablesTo Adjust Belts Auger Drive Traction Drive BeltTo Replace Belts Outdoors, away from fire orTraction DriveAuger Pulley is properly aligned with the traction drive beltOutdoors, away from fire or Arning Drain the gasoline flame Is not in the correct position, adjust as follows HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide If an adjustment is necessary, loosOutdoors, away from fire or How To Replace The Friction WheelTo adjust To Adjust or Replace the SparkplugHOW to Replace the Auger Shear Bolt 001088J27 Line outdoors, away from OtherSnow Thrower Correction TroubleCause Description Craftsman 26 9HP Snow Thrower 536.886260 Frame AssemblyScrew Electric Start AssemblyMotor Starter Frame Assy Frame AssemblyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Flatwasher Drive544 Auger Housing Assembly500 5OOCraftsman 9HP Snow Thrower Auger Housing Assembly593 582 Plastic Craftsman 26 9HP Snow Thrower Discharge Chute Assembly725 Handle AssemblyWasher Sptlk Handle UpperWasher 678 673 Wheel Assembly8OO Shift Yoke Assembly874 Chute Control ROD Assembly863 867 View from Auger Decals828 831 824Craftsman 4-CYCLE Engine Model Number Piston, Pin & Ring Set Craftsman 4-CYCLE Engine Model NumberKEY Part Description Gasket28820 298Incl EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.