Craftsman 536.88626 Maintenance and Storage, Slow Fast Electric Start Engine Start Engine Run

Page 4

13.Never operate the snow thrower near en- closures, automobiles, window wells, drop-offs, and the like without proper ad- justment of the snow discharge angle. Keep children and pets away.

14.Do not ovedoad the machine capacity by attempting to clear snow at too fast a rate.

15.Never operate the machine at high trans- port speeds on slippery surfaces. Look be- hind and use care when backing up.

16.Never direct discharge at bystanders or allow anyone in front of the unit.

17.Disengage power to the collector/impeller when snow thrower is transported or not in use.

18.Use only attachments and accessories ap- proved by the manufacturer of the snow

thrower (such as tire chains, electric start kits, ect.).

19.Never operate the snow thrower without good visibility or light. Always be sure of your footing and keep a firm hold on the h_ndles. Walk;never ran.

20.Do not over-reach.Keep proper footing and balance at all times.

21.Do not attempt to use snow thrower on a roof.

MAINTENANCE AND STORAGE

1.Check shear bolts and other bolts at fre- quent intervals for proper tightness to be

sure the equipment is in safe working condition.

2.Never store the snow thrower with fuel in

the tank inside a building where ignition sources are present such as hot water and

space heaters, clothes dryers, and the like.

Allow the engine (motor) to cool before storing in any enclosure.

3.Always refer to operator'sguide instruc- tions for important details if the snow

thrower is to be stored for an extended pedod.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the snow thrower a few minutes after

throwing snow to prevent freeze-up of the auger/impeller.

AWARNING:for use on sidewalks,This snow throwerdrivewaysis and other ground level surfaces.

Caution should be exercised while using on

steep sloping surfaces. DO NOT USE SNOW THROWER ON SURFACES ABOVE GROUND LEVEL such as roofs of resi- dences, garages, porches or other such structures or buildings.

IMPORTANT: Many of the following symbols are located on your unit or on literature sup. plied with the product. Before you operate the unit, learn and understand the purpose for each symbol.

Control And Operating Symbols

Slow

Fast

Electric Start

Engine Start

Engine Run

I I-I N

Engine Off Engine Stop

On

Choke Off

Choke On

Neutral

®®

Throttle

Primer Button

Ignition Key

Ignition Off

Ignition On

F-001088J4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Snow Thrower 001088JWash Hands After Handling Training PreparationMaintenance and Storage Slow Fast Electric Start Engine Start Engine Run÷61 Drive Clutch Reverse Auger Clutch Auger Collector EngageNot actual size Tools Required for Assembly ThrowerTo Remove Snow Thrower From Carton ShifterLoosen To Assemble the Handle and Crank AssemblyRemove To Install Shifter Knob KnobShort LongSnow Chute Assembly HOW to SET the Length of the CablesHOW to SET the Skid Height Position snow chute on insideChoke Control Used to start a cold Know Your Snow ThrowerDown HOW to Move Forward and Backward To Stop Your Snow ThrowerTo Control Snow Discharge To USE Wheel Lockout PINService & Adjustments section of this manual Before Starting the EngineCheck the OIL Fill GASEquipped with a three-wire To Stop EngineTo Start Engine Cold StartRun engine at full throttle Fast when throwing snow Warm StartCold Start Warm StartSnow Throwing Tips Lubrication Chart Customer ResponsibilitiesManual After Each USEProduct Specifications AS RequiredLUBRICATION-EVERY 25 Hours LUBRICATION-NOT RequiredEngine LubricationTo Change Engine OIL Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightTo Adjust Belts HOW to Check and Adjust CablesRemove the belt cover. See Traction Drive Belt To Replace BeltsOutdoors, away from fire or Auger DriveOutdoors, away from fire or Arning Drain the gasoline flame Pulley is properly aligned with the traction drive beltTraction DriveAuger HOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideIf an adjustment is necessary, loos Is not in the correct position, adjust as followsHow To Replace The Friction Wheel Outdoors, away from fire orHOW to Replace the Auger Shear Bolt To Adjust or Replace the SparkplugTo adjust 001088J27 Snow Thrower OtherLine outdoors, away from Cause TroubleCorrection Craftsman 26 9HP Snow Thrower 536.886260 Frame Assembly DescriptionMotor Starter Electric Start AssemblyScrew Frame Assembly Frame AssyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Drive FlatwasherAuger Housing Assembly 5005OO 544Auger Housing Assembly Craftsman 9HP Snow Thrower593 582 Craftsman 26 9HP Snow Thrower Discharge Chute Assembly PlasticHandle Assembly 725Washer Handle UpperWasher Sptlk Wheel Assembly 678 673Shift Yoke Assembly 8OO863 867 Chute Control ROD Assembly874 Decals 828 831824 View from AugerCraftsman 4-CYCLE Engine Model Number Craftsman 4-CYCLE Engine Model Number KEY Part DescriptionGasket Piston, Pin & Ring SetIncl 29828820 EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

536.88626 specifications

The Craftsman 536.88626 is a versatile snowblower designed to tackle winter's greatest challenges. Perfect for homeowners looking to keep their driveways, walkways, and patios clear, this model boasts a combination of power, efficiency, and user-friendly features.

One of the standout characteristics of the Craftsman 536.88626 is its powerful engine. It typically features a robust gas engine, capable of producing ample torque to handle heavy, wet snow with ease. This ensures that users can rely on the snowblower to tackle the toughest winter conditions without significant effort. The engine's reliability is complemented by a reliable starting system, making the machine easy to operate in cold temperatures.

Another notable feature of this snowblower is its clearing width and intake height. The Craftsman 536.88626 usually comes equipped with a substantial clearing width, often around 24 inches, allowing it to cover large areas more efficiently. The impressive intake height ensures that it can scoop up deeper snow without clogging, making it suitable for varying snow conditions, from light flurries to heavy snowfall.

The snowblower is also designed with user comfort in mind. It typically includes an adjustable handle, allowing operators of different heights to use it comfortably. Moreover, heated hand grips may be available on some models, providing added comfort during extended use in frigid temperatures.

Technology is at the forefront of this machine's design, featuring a six-speed transmission system. This allows users to select the ideal speed for their snow removal tasks, whether they need to move quickly over paved areas or take their time on uneven terrain. The easy-to-use chute control lets users direct the snow where they want it, helping to create clean paths without unnecessary snow buildup.

Maintenance is also simplified with the Craftsman 536.88626. It typically comes with easy-access components, enabling users to perform routine checks and repairs without hassle. The durable construction materials are designed to withstand harsh winter conditions, ensuring longevity and reliability.

In summary, the Craftsman 536.88626 stands out in the snowblower market with its powerful engine, efficient clearing capability, and user-centric features. Whether facing a light dusting or a heavy snowfall, this machine is designed to make snow removal quick, easy, and efficient, making it a valuable tool for winter weather preparedness.
Top Page Image Contents