Husqvarna 1130SB owner manual To Throw Snow See Fig, Using the CLEAN-OUT Tool See Fig

Page 11

OPERATION

TO THROW SNOW (See Fig. 15)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 15

USING THE CLEAN-OUT TOOL (See Fig. 16)

In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent ac- cidental starting.

•Release the auger control lever and shut off the engine.

•Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

•Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting engine.

•Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous- ing and the discharge chute.

DISCHARGE CHUTE

 

CLEAN-OUT

 

TOOL

 

MOUNTING

 

CLIP

 

FIG. 16

11

TO MOVE FORWARD AND BACKWARD (See Fig. 17)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

•Squeeze traction drive control lever to handle to engage the drive system.

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

•Press downward on the speed control lever and move lever to desired position BEFORE engaging the trac- tion drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

•Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 17

POWER STEERING OPERATION (See Fig. 18)

Steering triggers are used to assist in steering your snow thrower. The triggers are located on the underside of each handle. When a trigger is squeezed, it disen- gages the drive wheel on that side of snow thrower and allows it to turn in that direction.

•To turn left – squeeze left side trigger.

•To turn right – squeeze right side trigger.

LH TURN

RH TURN

TRIGGER

TRIGGER

FIG. 18

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts KEY Part Description Auger 30 RH CARRIAGEBOLT5/16−18X.625Auger 30 LH Skid Plate Repair Parts Auger Housing / Impeller AssemblyPlastic Retainer CARRIAGEBOLT5/16−18X.750 Weight BARKnob Black Deflector Control AssemblyChute Weldment Deflector Weldment532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly GrayLower Tube 532 42Handles 13 532 41 54-33 Shifter Plate Bracket Clutch RODRear Plate Bulb 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight Flange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate Gear14 15 11 532 18 40-76 Shifter Support Bracket 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate WeldmentClik PIN Axle ShaftRoll PIN 3/16 GearBottom PAN Repair Partschassis / Engine / PulleysEngine TEC Model FrameSteer Cable Bracket RH Steer Cable Bracket LHLever PIN Wheel LobeAxle Lobe Wrench Power Cord532 03 50-62 Safety Ignition KEY Retainer PIN10 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement
Top Page Image Contents