Husqvarna 1130SB owner manual Clutch ROD, Rear Plate, 13 532 41 54-33 Shifter Plate Bracket

Page 29

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

10

2

10

1

	3
9
	8
		5
	4
			7
				18
5	18		17	19
	18		19	19
		18	19
		18		15
				15
				14
	10
6	16
	17	13 19
	01.12.006-C			12
	01.12.006-C

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 18 04-80 IMPELLER ROD ASSEMBLY

2532 40 57-40 TRACTION ROD ASSEMBLY

3532 18 04-45 SHIFTER ROD TOP

4532 18 77-16 SHIFTER ROD BOTTOM

5532 18 04-47 SPRING SLEEVE

6532 17 86-69 IMPELLER SPRING

7532 18 09-26 TRACTION SPRING

8872 27 05-06 CARRIAGE BOLT 5/16−18 X .750

9	532 15 53-77	NUT 5/16−18
10	532 16 96-75	RETAINER
11	532 40 33-00	CLUTCH ROD
12	532 41 69-21	REAR PLATE

13532 41 54-33 SHIFTER PLATE BRACKET

14532 41 68-64 CLUTCH PLATE BRACKET

15532 41 54-35 CLUTCH PLATE

16532 41 54-50 SHIFTER PLATE

17817 00 05-12 BOLT 5/16−18 X .750

18532 40 28-81 SHOULDER BOLT 1/4−20 X .500

19	532 19 17-30 NUT 1/4−20

11

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29

Image 29

Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts KEY Part Description Auger 30 RH CARRIAGEBOLT5/16−18X.625Auger 30 LH Skid Plate Repair Parts Auger Housing / Impeller AssemblyPlastic Retainer CARRIAGEBOLT5/16−18X.750 Weight BARChute Weldment Deflector Control AssemblyDeflector Weldment Knob Black532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly GrayLower Tube 532 42Handles 13 532 41 54-33 Shifter Plate Bracket Clutch RODRear Plate Bulb 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight Assembly Rubber Wheel Ring 532 40 61-09 Control Shaft Assembly532 18 00-82 Intermediate Gear Flange Bearing14 15 Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment 11 532 18 40-76 Shifter Support BracketRoll PIN 3/16 Axle ShaftGear Clik PINEngine TEC Model Repair Partschassis / Engine / PulleysFrame Bottom PANSteer Cable Bracket RH Steer Cable Bracket LHLever PIN Wheel LobeAxle Lobe 532 03 50-62 Safety Ignition KEY Power CordRetainer PIN Wrench10 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement