Husqvarna 1130SB owner manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to a qualified service centre.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Refill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position.

4.

Move throttle to FAST position.

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact a qualified service centre.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts.

vibration

 

augers or impeller.

 

If vibration remains, contact a qualified service centre.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact a qualified service centre.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Image 19
Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts KEY Part Description Auger 30 LH CARRIAGEBOLT5/16−18X.625Auger 30 RH Plastic Retainer Repair Parts Auger Housing / Impeller AssemblySkid Plate CARRIAGEBOLT5/16−18X.750 Weight BARKnob Black Deflector Control AssemblyChute Weldment Deflector Weldment532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly GrayLower Tube 532 42Handles Rear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Flange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate Gear14 15 11 532 18 40-76 Shifter Support Bracket 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate WeldmentClik PIN Axle ShaftRoll PIN 3/16 GearBottom PAN Repair Partschassis / Engine / PulleysEngine TEC Model FrameSteer Cable Bracket RH Steer Cable Bracket LHAxle Lobe Wheel LobeLever PIN Wrench Power Cord532 03 50-62 Safety Ignition KEY Retainer PIN532 18 10-35 DECAL, DANGER, Deflector Decals10 532 18 37-30 DECAL, Remote Deflector Warranty Statement