Husqvarna 1130SB owner manual CARRIAGEBOLT5/16−18X.750, Weight BAR

Page 24

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

1

							KEY	PART	DESCRIPTION
				3		2	NO.	NO.	DESCRIPTION
						2
							1	532 18 47-47 DRIFT CUTTER BAR
				4			1	532 18 47-47 DRIFT CUTTER BAR
							2	872 27 05-06	CARRIAGEBOLT5/16−18X.750
							3	532 17 92-46 PLASTIC WASHER
			5	4	3		4	810 04 05-00 LOCKWASHER 5/16
1		4		4			5	532 12 86-38	NUT 5/16−18
	3	4
	3		5
			5
		3	4
2		3
2
				01.16.001-A

	2
	4
2		KEY	PART	DESCRIPTION
2		NO.	NO.	DESCRIPTION
1		1	532 18 25-16	WEIGHT BAR
1		2	872 11 05-10 CARRIAGE BOLT 5/16−18
4				X 1.25
		3	532 75 11-53	NUT 5/16−18
	3	4	819 11 22-06	WASHER
	3

01.17.003-B

3

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

24

Image 24

Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger 30 LHAuger 30 RH Repair Parts Auger Housing / Impeller Assembly Plastic RetainerSkid Plate Weight BAR CARRIAGEBOLT5/16−18X.750Deflector Control Assembly Chute WeldmentDeflector Weldment Knob BlackLEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket532 42 Lower TubeHandles Clutch ROD Rear Plate13 532 41 54-33 Shifter Plate Bracket 532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightBulb Rubber Wheel Ring 532 40 61-09 Control Shaft Assembly Assembly532 18 00-82 Intermediate Gear Flange Bearing14 15 532 19 84-74 Speed Selector Head Assembly Trunnion Bearing Assembly532 19 77-63 Drive Plate Weldment 11 532 18 40-76 Shifter Support BracketAxle Shaft Roll PIN 3/16Gear Clik PINRepair Partschassis / Engine / Pulleys Engine TEC ModelFrame Bottom PANSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe Axle LobeLever PIN Power Cord 532 03 50-62 Safety Ignition KEYRetainer PIN WrenchDecals 532 18 10-35 DECAL, DANGER, Deflector10 532 18 37-30 DECAL, Remote Deflector Warranty Statement