Husqvarna 1130SB owner manual Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
	NYLON	BETWEEN
	WASHER	HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

Image 7

Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts KEY Part Description Auger 30 LH CARRIAGEBOLT5/16−18X.625Auger 30 RH Plastic Retainer Repair Parts Auger Housing / Impeller AssemblySkid Plate CARRIAGEBOLT5/16−18X.750 Weight BARKnob Black Deflector Control AssemblyChute Weldment Deflector Weldment532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly GrayLower Tube 532 42Handles Rear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Flange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate Gear14 15 11 532 18 40-76 Shifter Support Bracket 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate WeldmentClik PIN Axle ShaftRoll PIN 3/16 GearBottom PAN Repair Partschassis / Engine / PulleysEngine TEC Model FrameSteer Cable Bracket RH Steer Cable Bracket LHAxle Lobe Wheel LobeLever PIN Wrench Power Cord532 03 50-62 Safety Ignition KEY Retainer PIN532 18 10-35 DECAL, DANGER, Deflector Decals10 532 18 37-30 DECAL, Remote Deflector Warranty Statement